answersLogoWhite

0


Best Answer

This is likely to be caused by the ageing of components, specifically the plastics used for insulation. Dust and humidity will sometimes contribute to it, but not with new components. Some suggest that it is possible to seal the components with black silicon to prevent a repeat. However, the components that are affected carry up to 30000 volts. Not only do they operate at that voltage but they can retain that voltage for days or weeks after the television was last used. Don't under any circumstances try to repair a television unless you are properly trained and qualified to do so.

User Avatar

Wiki User

โˆ™ 2009-02-13 04:49:25
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Would a onetime snap and pop high voltage arc in a ten year old projection TV be more likely caused by dust and humidity or the aging of components?
Write your answer...
Submit
Related questions

Why is a voltage regulator important?

To protect voltage sensitive components of an electrical circuit.


How does temperature affect the voltage in a series circuit?

If the temperature is changed in a series circuit, the components will get hotter. This increased temperatures in the components then serves to increase the voltage of the circuit.


What are regulatory components?

Regulatory components in short to say they are the components which regulate the input voltage and current applied to the electrical and electronic devices as well as machines also........... In shortly it will stablise the voltage and current and this components are used in stablisers........ It also prevents machines and devices from damage..............


Is there a formula to calculate the breakdown voltage of air at specific temperatures pressures and humidity over a distance?

Yes, ball sparks gaps is the official way to calculate the breakdown voltage of air at specific temperatures pressures and humidity over a distance.


Why does the picture bend upwards in the bottom left corner of a Philips 55 projection television?

Picture bowing and bending on a projection TV is usually caused by an out-of-spec power supply voltage that is not providing sufficient voltage for proper screen deflection. Seek qualified service for this unit.


What is the voltage range in which ESD can affect computer components?

4


What is the voltage range in which esd can effect components?

10 Volts


What is a voltage divider circuit?

The voltage divider circuit is a network of two or more components in series, often resistors, between a potential difference. The voltage between the components will be somewhere between the potential difference across the whole network and so divides the total voltage into one or more intermediate voltages.


What are the used of passive components in electronics?

passive components can store the energy in the form of current or voltage , which is useful in electronics circuits.


What is the purpose of voltage regulators?

Voltage regulators are intended to keep a certain voltage level, which is important for most electronics to run properly. Without a voltage regulator, if an electronic, such as a computer, receives too much voltage then it can fry the components.Controls output of alternator so battery does not over or undercharge Should control voltage range from (when engine running) 13.8-14.2 volts Without voltage regulator: Voltage could go to 18-24 volts causing electrical components to burn out


How do the components of an electrochemical cell produce voltage?

Go screw off


What is total voltage in a series circuits?

In a series circuit the total voltage is the sum of the voltage drops across all the component in series. When the voltage drops across each the individual components are added up, they will equal the supply (or applied) voltage.


How does a current source works?

Basically current sources are made from Voltage sources by adding some extra components to voltage souce.


Where are resistors placed to control voltage and current?

A: A RESISTOR is a passive component it cannot control voltage these components and/or current it can however limit


What is the voltage in which ESD can affect components?

Most components are designed and built to work at very low voltage. ESD can be of a magnitude of 1000 times greater. So if this voltage can find its way into a circuit it can permanently damage the circuit or worst yet weaken it for a premature failure


110v into 220v?

in circuits to reduce or to add voltage is used coil components


What components comprise the excitation current of a transformer?

A transformer's excitation current can be resolved into two components. The first is in phase with the primary voltage, and is responsible for the losses. The second lags the supply voltage by 90 degrees, and is responsible for magnetising the core.


Whats the highest voltage increase i can make when replacing a Capacitor?

you cannot increase the voltage by replacing a capacitor. A capacitor is a passive components it has no gain.


What is the function of optical isolation in plc processor?

To protect the low voltage electronic components in the PLC from High Voltages/Currents such as in voltage spikes.


What components are used to change an AC voltage to a lower or higher value?

Step up transformers are used to increase the voltage to a higher value


What are travel voltage converters used for?

There are many uses of travel voltage converters. Travel voltage converters allow one to change the voltage of an electrical power source. This product can be combined with other components to create a power supply.


How can transformer oil be used in transformers with voltage rating above its breakdown voltage?

In this circumstance, the clearance between components at different potential must be increased.


What is true about the sum of the voltages across the components in a circuit compared to the voltage of the cell?

voltage is devided only in series circuit and is the same at the parallel circuit


Are Voltage and Current two important components to robotics?

Voltage and current are important parameters in any electrical and electronic devices and apparatus, including robotics.


Individual components in a parallel circuit experience the same?

Voltage