0
What else can I help you with?
Can you connect tv to a projector?
If you TV has output connection, then you can get cables to connect your TV to your projector. For example I have a TV with RCA video and audio outputs, I use 3 RCA cables and then I connect them to my RCA inputs into my projector. My projector has a small speaker, so most of the time I just connect the video cable.
How can I connect a mixer to an audio interface?
To connect a mixer to an audio interface, use balanced cables to connect the mixer's main outputs to the audio interface's line inputs. Adjust the levels on the mixer and interface to ensure proper signal flow and avoid clipping.
How do you connect numark mixdeck to speakers?
To connect a Numark Mixdeck to speakers, first, locate the main output ports on the back of the Mixdeck, which typically include XLR, RCA, or 1/4-inch TRS outputs. Use the appropriate cables to connect these outputs to the corresponding inputs on your speakers or amplifier. If using powered speakers, simply connect the Mixdeck directly; for passive speakers, ensure you connect to an amplifier first. Finally, power on your speakers and Mixdeck to start mixing.
Where do the cables from a Purtone HPD -710 connect to on to a Emerson tv?
The Purtone HPD-710 system consists of passive speakers that need an amplifier to drive them. Unfortunately, even the subwoofer needs an amp. An Emerson TV will not have speaker outputs, it will have RCA line-level outputs. You must plug the TV into a surround-sound receiver to amplify the signal. Then connect speaker cables from the receiver to the Purtone speakers. Since the sub has no amp, you will need a receiver with a subwoofer amp function, which are not common.
How do you connect a lexicon mx200?
To connect a Lexicon MX200, first, ensure that the unit is powered off. Use balanced XLR or TRS cables to connect the outputs of your audio interface or mixer to the MX200's inputs, and then connect the outputs of the MX200 back to your audio interface or mixer. Finally, power on the MX200 and select the appropriate input and output settings in your audio software to ensure proper routing. Make sure to check levels and adjust settings as needed for optimal performance.
Why does the gas gusge spin 380 degrees any time the battery is disconnected 1998 Malibu?
1. UN HOOK THE BATTERY CABLES. 2. TOUCH THE ENDS OF THE LOOSE CABLES TO EACH OTHER FOR 5 SECONDS. 3. CONNECT CABLES BACK TO BATTERY, POSITIVE FIRST. This is the advise I found on line.
How do you fit 6 by 9 in a peugeot 106?
you need to start by fitting them into the parcell shelf, run the cables under the back seats and then under the carpet on the passenger side. there is a slight gap in the side of the head unit slot and behind the glove box to run the cables through. on the ISO cable from your head unit there should be 4 cables that arn't on the other side of the connection, these are your speaker outputs that you need to snip and connect to your speaker cables, making sure you connect the positive with the positive and the nagative with the negative.
How do you connect brennan jb7 to an external amplifier?
To connect a Brennan JB7 to an external amplifier, first, locate the audio output jacks on the back of the JB7, which typically include RCA outputs (red and white connectors). Use a pair of RCA cables to connect these outputs to the corresponding inputs on your external amplifier. Ensure the amplifier is powered on and set to the correct input source to hear audio from the JB7. Finally, adjust the volume levels on both the JB7 and the amplifier for optimal sound.
How can I hook up a surround sound system in my home?
To hook up a surround sound system in your home, first, identify the audio outputs on your TV or media player. Then, connect these outputs to the corresponding inputs on the surround sound receiver using the appropriate cables. Next, connect the speakers to the receiver, making sure to match the correct polarity. Finally, power on the system and adjust the settings to optimize the sound for your room.
What do you need to connect two hard drive and one CD burner?
You need two cables called IDE cables. Typically these cables have the ability to connect two hard drives or two CD DVD roms. So just find two IDE cables and you can conect what you need to connect.
Do I need cables to connect my computer to TV?
Yes, you do need cables to connect your computer to your television. You can also use the guide to find out about what type of cable that you need to connect the computer to the television.
What are drive cables?
They are the cables that connect your hard drive or cd/dvd drive to the motherboard.
