0
Most consider toilet repair easier than replacement. However, many things need to be considered before deciding whether or not to fix or replace it. A toilet has a base, tank, seat, lid, flush handle and water line on the outside. Inside the tank are a fill valve that controls the incoming water and a flapper valve that controls water going from the tank to the bowl when the flush handle is pressed. Most tanks are attached to the base with two bolts and washers.
Toilet repair usually begins when the flapper valve leaks water from the tank to the bowl, and it causes the tank to keep refilling though no one has flushed the toilet. Many times it is just the chain that lifts the flapper valve getting caught or twisted. This is a 30 second toilet repair. Replacing the flapper valve only requires cleaning the surface it closes on and 30 seconds to replace the flapper with a new one.
Replacing the inlet valve is another toilet repair that only takes about 15 minutes for a novice who can follow written instructions. An inlet valve needs replaced when obvious leaking is spotted or a simple adjustment of the float assembly does not stop the water from overfilling the tank.
It is a more involved task to replace the rubber washers and bolts where the tank meets the base, but it is still a job that can be tackled by a novice who can read and follow written instructions included with the parts. The main concern of replacing most any component of a toilet is over tightening and breaking the tank or base.
If a toilet looks bad or a new design is desired, it still can be replaced by a novice. If the floor around the toilet is solid with no signs of rotting due to leakage, and if the toilet flange is intact, it takes about an hour for a novice to replace the toilet. Without a toilet jack to lower a toilet onto the wax ring that seals the toilet to the toilet flange, it is important to have two other helpers. Two are needed to slowly lower the toilet with the attached wax ring onto the flange while the other watches from floor level to be certain of the alignment of wax ring to toilet flange. Go slow and do not over tighten parts and that toilet can be new or good as new in no time.
What else can I help you with?
How do you fix singing toilet?
Just replace the ballcock valve..
How can I fix a toilet that rocks?
To fix a rocking toilet, you can try tightening the bolts at the base of the toilet using a wrench. If that doesn't work, you may need to replace the wax ring or use shims to stabilize the toilet.
How can I fix a toilet seal?
To fix a toilet seal, you will need to remove the toilet, replace the wax ring seal, and then re-install the toilet. Make sure to clean the area thoroughly before re-installing the toilet to ensure a proper seal.
How can I fix a toilet seal that leaks?
To fix a leaking toilet seal, you will need to replace the wax ring that seals the connection between the toilet and the floor. This involves removing the toilet, cleaning the area, and installing a new wax ring before reattaching the toilet.
How do you fix a leaky toilet?
Where is it leaking ? Flapper in the tank, replace flapper. Between tank and bowl, separate and replace the seal. Toilet to floor. Replace the wax ring under the toilet, making sure it is thick enough to form a seal and the bolts are installed correctly and holding the toilet down.
What are the common causes of a toilet leak at the base and how can it be fixed?
Common causes of a toilet leak at the base include a damaged wax ring, loose bolts, or a cracked toilet base. To fix it, you can replace the wax ring, tighten the bolts, or replace the toilet if it is cracked.
How can I fix a leaking toilet base?
To fix a leaking toilet base, you can start by tightening the bolts at the base of the toilet. If that doesn't work, you may need to replace the wax ring or the toilet flange. It's important to turn off the water supply before attempting any repairs.
How can I fix a toilet wax ring leak?
To fix a toilet wax ring leak, you will need to remove the toilet, replace the wax ring, and then re-install the toilet. Make sure to clean the area thoroughly before installing the new wax ring to ensure a proper seal.
How can I fix a loose toilet?
To fix a loose toilet, you can try tightening the bolts at the base of the toilet using a wrench. If that doesn't work, you may need to replace the wax ring underneath the toilet or use shims to stabilize it. If you're unsure, it's best to consult a professional plumber for help.
How can I fix a float in a toilet?
To fix a float in a toilet, you can adjust the float arm or replace the float assembly. First, locate the float inside the toilet tank. If the float arm is bent, straighten it out. If the float is damaged or not working properly, you may need to replace it with a new one. Make sure to turn off the water supply to the toilet before making any repairs.
How can I fix a toilet leaking from the tank bolts?
To fix a toilet leaking from the tank bolts, you can try tightening the bolts with a wrench. If that doesn't work, you may need to replace the bolts and washers to create a better seal.
Why is my toilet rocking from front to back and how can I fix it?
Your toilet may be rocking from front to back due to loose bolts securing it to the floor. To fix this issue, you can try tightening the bolts at the base of the toilet using a wrench. If the problem persists, you may need to replace the wax ring or shim the toilet to stabilize it.
