0
If you perform vehicle repairs within your own personal garage, pole barn or other building structure around your residence, you may find that installing a vehicle lift can make your work much easier. When using vehicle lifts to work on areas such as the undercarriage of your automobile, you take away the need for blocking the vehicle and using unstable jacks to raise the car to a workable level. Ultimately the vehicle lift can help to create safer working conditions and can decrease the length of time necessary for performing the actual repair work.
Before purchasing a vehicle lift to install for your personal use, it is important to make sure that the floor of the building meets certain specifications. These specifications are important to insure that the vehicle lift will be properly supported. Different model vehicle lifts may carry special requirements that are set in place by the individual manufacturer. However, when it comes to the floor specifications, most of the model vehicle lifts that are available for residential use are usually the same.
Make Sure You Have Adequate Floor SpaceTo insure that you will be able to operate the vehicle lift safely you will need an adequate amount of floor spacing to work with. Depending on whether you select a two-post or four-post auto lift will determine the amount of floor space that you will need. This is determined by the width and height to safely lift the vehicle while providing you with a safe space to work in. You should always leave enough room to maneuver around when working on your vehicle without the risk of bumping into equipment or having equipment block you in if there is an emergency. This space should be set in a manner in which you leave room and space around the lift to move and work with needed equipment and tools as well. Concrete Floor RequirementsWhen installing a vehicle lift in a residential outbuilding, the building should contain a concrete foundation to build the lift on. The concrete that is used for this foundation will need to have a rating that allows for 3,000 pounds of pressure per square inch. Concrete is the only material that can be used for supporting the vehicle lift because of the need to distribute the weight of both the vehicle lift and the vehicle it is holding. Concrete that does not meet this rating can be cracked under this amount of pressure causing the vehicle to fall and injure anyone that may be in the area. Floors Must Be Level before Installing the LiftInsuring that the floor of your outbuilding is level will help to create a safer working condition. Even the slightest slop in the floor can greatly affect the ability of the vehicle lift to support vehicles. This tilt can cause the vehicle to slide off from the lift when it is raised in the air. Due to the seriousness of this requirement you may want to hire a professional to inspect the floor for you. If it is necessary to pour a new concrete foundation or add to your existing concrete floor, you will need to wait for 30 days after completing the floor before installing the vehicle lift. This will allow the cement to harden to its peak.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Why would Brake pedal on ford zx2 stay up with car off but go to floor when car is turned on?
Vacuum booster is working--When vehicle off there is no vacuum assist (for power brakes) When vehicle is on vacuum is present Brake pedal going to floor is another problem--no fluid in master cylinder? Leak in system? Brakes not adjusted properly?
What is the floor area of NASA Vehicle Assembly Building?
The approximate floor area of NASA Vehicle Assembly Building is 129,428,000 cubic feet.
Many over seas container shipments are floor loads what does the term floor loads mean?
Over sea shipment containers are considered floor load. Floor load refers to the floor safely capable of supporting the structure.
Many over seas container shipments are floor loads what does the term floor load mean?
Over sea shipment containers are considered floor load. Floor load refers to the floor safely capable of supporting the structure.
How are different floors in houses put together without having them fall onto the bottom floor?
they have supporting beams in the walls of the lower floor
On sims 3 your sim keeps floating to the bottom floor after she finishes an action.. how do I stop it?
that sounds like a big problem, i would try reinstalling your game, and checking if your computer meets the system requirements for the game to work properly.
What are the requirements for one's home in order to have Nuheat floor heating systems?
There are no requirements for one's home, because Nutheat floor heating systems can simply adhered to the subfloor and the flooring can then be installed over top.
How to calculate floor support requirements?
To calculate floor support requirements you need to calculate the maximum load. Determine the breadth of the joist, span and fiber stress for each floor system. In addition, you will need to determine the total area supported and divide it by one joist.
How do you keep floor tiles sparkling?
The floor can spark by cleaning properly. This can be possible through technical persons. We have more experience to make floor with stylish titles.
Which type of floor opening is described below Floor opening measuring 12 inches or more in its least dimension located in a floor platform pavement or yard To be properly guarded a floor openi?
typical floor opening
Wegeners hypothesis of continental drift was finally confirmed by?
evidence supporting the idea of sea-floor spreading.
What is the consistancy of floor leveler need to be?
for floor leveler to work properly and effectively it should be a little thinner than paint when you are stirring it. this will let it flow to the low spots needed to cover the floor properly. floor leveler's are quick drying and shouldn't be kept waiting to pour, as soon as you mix it up pour it or you will waste it.
