0
The varying temperatures found within the summer and winter seasons will have you adjusting the thermostat multiple times through the day. There may be, however, more money being spent in the heating and cooling of your house then actually needed. This extra cost may be caused by inaccurate readings coming off of your thermostat due to bad calibrations. Here are a few steps that can be run through to check and modify the calibrations of your home thermostat.
•The first step would be to head down to the local hardware store or drug store to purchase a glass thermometer that uses Mercury for readings. This thermometer will be set as close as possible to the thermostat using some sort of adhesive, such as tape or glue.
•Once the thermometer has been in place for a few days to adapt to the air and temperature of the home, compare the readings on the thermometer with the readings of the thermostat at one hour intervals. If the temperatures are off by more than five degrees, it may be necessary to re-calibrate your thermostat.
•Remove the cover of the thermostat and clean the area using an air cleaner normally used for keyboards and computer equipment. Once that dirt has been properly removed, use a paper towel that is a little damp to clean all of the components within the device.
•The next step would be to un-screw the screws holding the thermostat to the wall and then removing it completely from where it is currently housed. There will be wires coming from the wall in a very small opening. The readings being wrong may be caused by the opening being larger than needed and causing air to effect the readings. This area around the wires can be plugged accordingly using a caulking compound and a painter’s stick.
•The thermostat can then be reattached with the screws and adjusted so that everything is perfectly straight up and down on the wall. Once the cover has been reattached, the same procedures as before with the glass thermometer should be followed to obtain an accurate reading.
•If the readings are still not up to standard, a new thermostat would have to be purchased and installed within your home.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Three steps in calibrating a thermometer?
stik a thermometer in to a girls private when they have their period
What are the step you follow for calibrating an equipment?
The steps for calibrating a piece of equipment generally compare your apparatus against some reference standard.Consider calibrating a stopwatch. You may calibrate this against radio supplied time signals, some for a short period, some for a 1 hour period. And repeat the measurements several times, and ignore any measurement that appears out of range when compared with all the rest.Sometimes there are such aids as standard solutions or materials, from authoritative suppliers as a standards laboratory. Or calibrated sets of masses, certified by a standards lab.Make sure the comparisons are made under appropriate repeatable conditions of altitude, heat, and so on for other environmental variables.
Why are the temperatures of the melting point of ice boiling point of water called fixed point in calibrating the thermometer?
it is because they were consistent at melting and boiling point
Why there is no fluid coming from the radiator to the thermostat hosing?
The coolant is pumped from the thermostat housing into the top of the radiator but not until the thermostat opens.
What is the difference between a thermostat and a thermometer?
A thermostat controls temperature, a thermometer measures it.
Three steps in calibrating a thermometer?
stik a thermometer in to a girls private when they have their period
What cars have to have a thermostat?
All cars need a thermostat for proper operation and longevity.
Does the thermostat have to be in the Plymouth Voyager?
Yes, the thermostat needs to be installed for proper engine operation.
What is the proper thermostat degree for a 1994 Nissan Pathfinder?
A 180 and a 170 degree thermostat are listed for it.
What causes Grill pilot light on wolf salamamder grill to keep going out thermocouple ok valve new?
If a Salamander Grill keeps going out and the thermocouple is okay and the valve is new then a faulty thermostat could be the cause. Replacing the thermostat or re-calibrating it generally solves the issue.
Where is the thermostat in a 2000 Lexus RX 300 SUV?
the thermostat is under the air assembly,monted onto the cylinder head.there are three screws holding the thermostat,remove screws,dissconnet the housing and pull the thermostat out.Assembly is the reverse steps the thermostat is under the air assembly,monted onto the cylinder head.there are three screws holding the thermostat,remove screws,dissconnet the housing and pull the thermostat out.Assembly is the reverse steps
What does it mean when calibrating drive in circle come on your dash?
compass needs to be recalibrated
Can an automotive rookie replace a thermostat on a 2000 Dodge Caravan and if so what are the steps involved?
Too many steps and little things you should know. Spend $10 and buy a repair manual for your car at any auto Parts Store. You have two choices, Hayne's or Chilton's. A rookie can do this with the proper guidance. Get the manual and go for it. answer to remove thermostat dump coolant from engine remove top radiator hose from where it attaches to engine remove fitting,generally 2 or 3 bolts, where radiator hose attached this is called thermostat housing u will then see thermostat take notice of how the thermostat is seated as sometimes they can be installed upside down, upside down will not work correctly so then install proper temp new thermostat and new gasket reinstall thermostat housing' reattach radiator hose. refill engine and radiator with coolant start engine ,check for leaks if no leaks, job well done is easier than it sounds
How do you know if the thermostat went out in a Chrysler lebaron?
If the thermostat is stuck open, the engine will never warm up to proper temperature.
How hard it is to change the thermostat on a 2002 Chevrolet Malibu?
It is not hard if you have the proper tools. Drain the radiator and remove the upper hose at the engine. Remove the thermostat housing and install the thermostat. Clean the surfaces and install the new thermostat.
What is the proper process for replacing the thermostat on a 2001 Pontiac Grand Grix 3.1 V6?
remove all the coolant in the system take out thermostat put new thermostat in fill system...
What should be done after calibrating an instrument?
Test
