0
What else can I help you with?
How do you remove the heater core on a 1977 Cutlass Supreme?
To remove the heater core on a 1977 Cutlass Supreme, first, disconnect the negative battery cable and drain the coolant from the radiator. Next, remove the dashboard and any necessary components to access the heater core housing. Disconnect the heater hoses from the core, unbolt the housing, and carefully remove the heater core. Finally, reverse the process to install the new heater core and reassemble the dashboard.
How do you replace a heater core on a 1984 cutlass supreme 231 rear wheel drive?
The heater core on a 1984 Cutlass Supreme is located under the blower motor on the passenger side of the car, under the hood. First you need to remove the blower, and the hoses connecting the heater core. Replace the core, re-attach the hoses, and put the blower motor back on.
How do you remove heater blower on a 2005 Chevrolet Cavalier?
Remove the wiring harness from the back of your 2005 Chevy Cavalier heater blower motor. Remove the heater blower motor retaining bolts. Remove the heater blower fan.
How do you change a blower motor on a 1995 cutlass supreme?
Remove the wiring harness from the back of your 1995 Oldsmobile Cutlass blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.
Where is the heater blower motor resistor on a 2004 Malibu?
The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.
How do you replace heater blower fan on a 97 Toyota RAV4?
Remove the wiring harness to the heater blower fan. Remove the retaining bolts. Remove the fan from the blower. Reverse the process to install the new heater blower fan.
How to change the heater blower motor on a 1988 Oldsmobile cutlass ciera?
It's on the firewall up high on the passenger side. You may need to remove the alternator to get it out.
How do you replace a front heater core in 1999 b3500 dodge van?
Remove the grille panel, the cowl grille support panel, the right headlamp assembly, and the right radiator core support assembly.From inside the vehicle, remove the glove box bin, the right spot cooler duct, and the lower instrument panel skirt.Through the glove box opening and from under the instrument panel, remove the screws and nuts that secure the heater-A/C housing to the dash panel.Remove the screws that secure the flange connection between the heater-A/C housing and the blower housing.Separate the heater-A/C housing from the blower housing, and carefully remove the heater-A/C housing from the vehicle.
How do you remove the heater blower motor on a 1998 Ford Contour?
You remove the heater blower by removing the bottom cover of the Glove Compartment. Then you will see The heater blower housing. Then you will see like a black clip you need to lift. Then You simply turn clockwise and bingo its off. To install just do the same thing except in reverse mode. Good Luck!!
Where is the blower motor resistor on a 1998 Chrysler Sebring?
Fig 15 Blower Motor ResistorNOTE: The blower motor resistor is located on the lower right side of the heater housing.REMOVAL# Remove lower right underpanel silencer/duct. # Disconnect wiring connectors on blower motor resistor. # Remove blower motor resistor retaining screws. # Pull blower motor resistor out of heater housing.
Removing heater blower motor on a 1988 dodge dynasty?
Disconnect the battery. Remove the glove box to instrument panel screws. Disconnect the power and ground wires from the blower.. Remove the recirculating door actuator, the seven screws and then remove the complete recirculating housing.. Remove the three blower motor attaching screws.. Remove the blower motor...
How do you change the heater blower motor in an olds cutlass ciera 1989?
unplug the blower motor (electrical) Unbolt the blower moter Remove the alternator Remove the top powersteering bracket bolt Loosen the lower powersteering bolt Pry the powersteering pump towards the front of the car as much as possible Have a freind pry the engine towards the front of the car while you rotate and turn the blower motor out of the housing. Caution do not bend the fins on the blower motor. Its a tight fit but will come out with the right angle
