0
Well, honey, the torque sequence for the upper intake manifold on a 1995 Oldsmobile 98 is a piece of cake. You start in the middle and work your way out in a criss-cross pattern, tightening those bolts to about 89 inch-pounds. Just make sure you're using a reliable torque wrench and you'll be good to go, darling.
What else can I help you with?
What is the torque specs sequence for a intake manifold on a 2002 Lincoln ls 3.0 dual overhead cam?
There is no torque spec for the air filter --it sits in its housing which snaps open and closed.The intake manifold torque specs are 89 inch pounds (7.5 ft.lbs.), that is for both the upper and lower intake.
What is the torque for a 1999 Ford Taurus 3.0 upper intake manifold?
torque for bolts upper intake 1999 ford taurus 3.0 dohc
What is the torque specs for upper intake manifold on a 2003 Malibu?
on 3.1 v6,it is---intake 10 ft lbs-----upper intake-18 ft lbs,
What are torque specs for intake manifold for Saturn sc1?
22ft pounds is the torque spec, The tightning sequence is as follows. Upper side: 8-4-1-5 Lower side: 7-3-2-6-9
What is the torque specs for 96 Chevy beretta z26 3.1?
Lower intake manifold bolt 115 in/lb. Upper intake manifold bolt 18 ft/.
What is the torque spec for 1997 3.8 buick lesabre intake manifold?
The lower intake manifold to cylinder head torque specification is 132 inch pounds. The upper plastic intake plenum to lower intake should be done in three steps 22 inch pounds, 44 inch pounds and thirdly 89 inch pounds. Be sure to follow the appropriate tightening sequence diagram.
What is torque specs upper intake 2004 Kia sedona 3.5l?
The torque specifications for the upper intake manifold on a 2004 Kia Sedona with a 3.5L engine are typically around 11-15 lb-ft (15-20 Nm). It's important to follow a specific tightening sequence to ensure even pressure across the intake manifold. Always refer to the vehicle's service manual for the most accurate and detailed information.
What is the bolt tightening sequence for the upper intake manifold for a 1999 Chevy Express 3500 5.7?
The bolt tightening sequence for the upper intake manifold on a 1999 Chevy Express 3500 with a 5.7L engine typically follows a specific pattern to ensure even pressure. Start by tightening the bolts in a crisscross pattern, beginning from the center and working your way outward. Generally, you would first snug all bolts to a low torque, then go back and tighten them to the specified torque value, usually around 11 ft-lbs for the upper manifold. Always refer to the vehicle's service manual for the exact specifications and sequence for your specific model.
What are the torque specs on upper and lower intake manifold for a 2001 Pontiac grand am 3.4 liter?
lower intake is 115 in pounds upper is 18 ft pounds
What is the torque on a 3800 series 2 lower and upper intake manifold bolts?
The recommended torque specification for the lower and upper intake manifold bolts on a 3800 Series II engine is typically around 18-22 ft-lbs (25-30 Nm). It's important to follow the manufacturer’s torque sequence and specifications to ensure proper sealing and avoid damage. Always refer to a service manual for the specific vehicle and engine for precise details.
Where is the upper manifold gasket located on a 2000 Chevy s10?
Assuming this is a 4.3L engine, the upper intake manifold gasket would be between the upper intake manifold and the lower intake manifold.
Where are the upper intake gaskets on a v6 2000 ford windstar?
The upper intake gaskets on a 2000 Ford Windstar V6 engine are located between the upper intake manifold and the lower intake manifold. To access them, you typically need to remove the upper intake manifold, which involves disconnecting various components like the throttle body, vacuum lines, and electrical connectors. Once the upper manifold is removed, you can replace the gaskets. It's advisable to follow a repair manual for specific steps and torque specifications.
