0
What else can I help you with?
What cause a 1998 ford contour to drain 12volts when off and not running?
Disconnect battery and put a bulb between the battery post and the disconnected lead, if a drain is there the bulb should light up. Then methodicly remove and replace each fuse one at a time, if the light goes out, that will indicate the circuit the drain is on. Good Luck
What is the controlled variable for a light bulb and battery?
The controlled variable for a light bulb and battery experiment would be the type of light bulb or battery used. Keeping these variables constant ensures that any changes in the experiment are due to the independent variable being tested.
Does the dash battery bulb effect the alternator charge?
If your battery is not being charged , the battery light will come on in your dash
Battery drain escort?
1. Remove the negative battery terminal. 2. Put a 12 volt bulb in between the cable end and the terminal on the battery. 3. If you are having a drain then the bulb will light up. 4. Watching the bulb pull the fuses one by one. 5. When the light bulb goes out after pulling a fuse this is the circuit that is being drained. 6. If after pulling a fuse the light gets dimmer but doesn't go completely out that means more than one circuit is draining the battery. Continue to pull fuses and put them back in to find the 2nd drain. When the light goes completely out you have found the second drain. For this diagnostic procedure make sure that everything is turned off on the car including the the dome light that comes on when the door is opened. Make sure the key is in lock and off. Make sure the trunk is shut.
What is the energy transformation of a battery lights a bulb?
The energy transformation that occurs when a battery lights a bulb is chemical energy (stored in the battery) being converted into electrical energy, which then powers the bulb, producing light and heat energy as a result.
What happens when a battery light the light bulb?
When a battery is connected to a light bulb, the electrical current flows from the battery through the wire, causing the filament in the light bulb to heat up and emit light. The battery acts as a power source, providing the necessary voltage and current to illuminate the bulb.
How do you replace bulb in corvette glove box?
To replace the bulb in a Corvette glove box, first open the glove box and remove any contents. Locate the bulb socket, which is usually at the back of the glove box; twist or pull it gently to remove it. Replace the old bulb with a new one, ensuring it's secure, and then reinsert the socket back into its place. Finally, close the glove box and test the new bulb to ensure it works.
What forms of energy are tranferred from battery to light bulb?
The forms of energy transferred from a battery to a light bulb are chemical energy (stored in the battery) being converted to electrical energy (flowing through the wires) and then to light energy and heat energy (produced by the light bulb).
Ho w do you change the glove box light bulb?
To change the glove box light bulb, first, open the glove box and remove any contents. Locate the light bulb socket, which is usually found at the back of the glove box. Gently twist or pull the bulb socket to release it, then remove the old bulb and replace it with a new one, ensuring it fits securely. Finally, reinsert the socket into its place and close the glove box.
How do you change a glove box light bulb for a 2003 Mazda 6?
To change the glove box light bulb in a 2003 Mazda 6, first, open the glove box and remove any contents. Locate the light bulb housing, which is typically found on the upper side of the glove box. Carefully twist or pull the bulb socket to remove it, then replace the old bulb with a new one of the same type. Reinsert the bulb socket into the housing, close the glove box, and test the light to ensure it works.
What is the conclusion for a battery powered light bulb?
what is a conclusion for a battery powered light bulb
What can you connect to a battery and bulb for the bulb to light?
To light a bulb using a battery, you need to connect the battery terminals to the bulb's terminals using conductive wires. The positive terminal of the battery connects to one terminal of the bulb, while the negative terminal connects to the other terminal of the bulb. This creates a complete circuit, allowing electrical current to flow and illuminating the bulb. Make sure the bulb is compatible with the battery voltage to ensure proper functionality.
