0
For 1987 - 1996 Dakota trucks : It is recommended that bolt and hole threads first be chased with appropriate taps and dies (dirty or damaged threads can affect torque readings). Also recommended is to coat the bolt threads with non-hardening sealant such as Permatex no. 2 or similar product. Install the all of the bolts finger tight to start. Then tighten in several steps to 50 ft-lbs in the following pattern (from 1 to 8 in order) --- 7 - 3 - 1 - 5 (top row) 8 - 4 - 2 - 6 (bottom row) Now repeat the same tightening sequence and pattern in several more steps to 105 ft-lbs to finish the job.
What else can I help you with?
What is the torque specs for cylinder head on a 1983 Honda GL1100 GoldWing?
The torque specifications for the cylinder head on a 1983 Honda GL1100 GoldWing are typically 29 lb-ft (39 Nm) for the initial torque, followed by a final torque of 43 lb-ft (58 Nm). It's important to follow the specified torque sequence to ensure even pressure across the head. Always refer to the service manual for specific procedures and additional details.
What is the torque on a Yamaha yz426 head bolts?
39 ft pound. 14/27/39. In stages.
What is the head bolt torque Honda rancher 2007 420es?
The head bolt torque specification for a 2007 Honda Rancher 420ES is typically set at 29 lb-ft (39 Nm) for the initial torque. After the initial torque, it's common to follow a specific sequence and perform a final torque of 47 lb-ft (64 Nm). Always consult the service manual for precise specifications and sequences to ensure proper installation.
Cylinder head torque settings for a 1996 Honda civic 1.6 liter engine?
For a 1996 Honda Civic with a 1.6-liter engine, the cylinder head torque specifications typically require an initial torque of 29 ft-lbs (39 Nm) in sequence, followed by an additional 90-degree turn, and then another 90-degree turn. It's important to follow the specified tightening sequence to ensure even pressure across the head. Always consult the vehicle's service manual for the most accurate and detailed information.
What are the cylinder head bolt torque specs for a Honda rancher?
The cylinder head bolt torque specifications for a Honda Rancher typically range from 22 to 29 ft-lbs (30 to 39 Nm) for the initial torque, followed by an additional angle torque of 90 degrees. However, it's essential to refer to the specific service manual for your model year, as specifications can vary. Always use a calibrated torque wrench and follow the correct sequence for tightening the bolts to ensure proper sealing and engine performance.
What are the cylinder head bolt torque settings on an Isuzu kb 200?
Torque settings: Phase 1. 29ft/lb or 39 Newton Meter 2. 54 73 3. 72 98
What is the head bolt torque specs for a Honda rancher?
The head bolt torque specifications for a Honda Rancher typically range from 22 to 29 ft-lbs (30 to 39 Nm), depending on the specific model and engine type. It's essential to follow a specific tightening sequence and perform a multi-step torque process to ensure even distribution. Always refer to the service manual for the exact specifications and procedures for your particular model year.
What is the head gasket torque specs on a 91 Geo Metro?
The head gasket torque specifications for a 1991 Geo Metro with a 1.0L engine typically require an initial torque of 29 ft-lbs (39 Nm) followed by a second pass of 44 ft-lbs (60 Nm). It's important to follow the specific sequence for tightening the bolts to ensure even pressure. Always refer to the vehicle's service manual for the most accurate and detailed information.
Which cylinder is cylinder number 1 on a 1995 Dodge van 39 engine?
Front of driver side head.
What is the recommended torque specification for head bolts on a 1999 ford 3.0 V-6 when replacing the head gaskets?
FIRST... Make sure you have the heads magna-fluxed and if no cracks then have them surfaced. SECOND... make sure you use NEW head bolts. make sure decks are clean and free of any oil. put head gasket on noting the up designation on the head gasket. tighten new bolts in sequence to 35-39 ft lbs. Loosen all bolts in sequence a full 360* turn. tighten bolts to 20-24 ft/lbs, then tighten bolts an additional 85-95* then repeat last step again an ADDITIONAL 85-95* 6 4 2 8 5 1 3 7 TORQUE SEQUENCE
What are the head bolt torque settings for a Nissan patrol 4.2 petrol?
Torque settings are , for the head bolts : These are done in three stages ... One... 39 - 44 nm Two ... 54 - 59 nm... Three.... tighten then to 90 degrees ( angle setting )
What is the head bolt specs for Honda rincon?
The head bolt specifications for a Honda Rincon typically include a torque value of around 29 ft-lbs (39 Nm) for the initial torque, followed by a further tightening to about 45 ft-lbs (61 Nm) in a specific sequence to ensure even pressure. It's essential to use new head bolts, as they are often designed to stretch and maintain clamping force. Always consult the specific service manual for your model year to confirm exact specifications and procedures.
