0
Open the rear door[s] and on the section of the body covered by the door when it is closed, you will see two Phillips screws.After you remove those screws, press in the tabs immediately above and below those screws.At this point it is a good idea to close the doors if you have the 'barn door' style rear doors.The entire tail light assembly will rotate laterally about 45 degrees or so to the left for a left tail light and the right for the right side.Gently push the opposite edge of the light assembly toward the body of the vehicle.There are two tabs that fit into guide holes on the body of the vehicle.As you pull and or rock it gently you will be able to remove the entire light assembly.Once the light assembly is removed,remove the electrical cable wrap from the holding tab on the bottom of the light assembly to allow for some slack to the wiring.Whichever bulb is out,turn signal,tail light, or brake light,push in the clearly visible tab on the base of the bulb connector, and rotate the entire plastic connector about 45 degrees counter clockwise.Once the connector is freed from the tail light assembly you can remove the bulb by pressing inward on the tabs at base of the bulb, one on each side.Replace the bulb ensuring to snap the bulb base connectors to the bulb holder.Replace the bulb following the reverse directions,re-attach the electrical cable in the tab to prevent it flapping loose.Place the entire light light assembly in ensuring the retaining tabs click back into place.Replace the two Phillips screws slowly and the entire assembly will set back into place.A small gap between the body and the assembly is normal, it does not sit edge to edge.
What else can I help you with?
How Replace brake light suburban?
expose back of bulb, turn to the left, replace bulb, return to socket, turn to the right
Why do your left rear tail light and blinker not work on your 1997 suburban?
Bulb is blown. Replace bulb.
How do you replace a 1999 suburban tail light bulb?
The tail light bulb on a 1999 Chevy Suburban is replaced by removing the retaining screws, pulling the bulb assembly away from the vehicle, and unscrewing the bulb. A new bulb can then be installed and the assembly screwed back in place.
How do you replace the rear brake light bulb on a 2004 Honda Civic?
How do you replace the rear brake light bulb on a 2001 Honda civic?"
How do you replace marker light bulb 2001 Mercedes Benz C320?
How do you replace 2001 Mercedes c320 front marker light
How do you replace brake light bulb on 2001 infiniti G20?
anonymously
How do you replace service engine light bulb on 98 gmc suburban?
To replace the service engine light bulb on a 1998 GMC Suburban, first disconnect the negative battery cable to ensure safety. Remove the instrument panel by unscrewing the necessary screws and gently pulling it out. Locate the bulb socket for the service engine light, twist it counterclockwise to remove, and replace the old bulb with a new one. Finally, reassemble the panel, reconnect the battery, and check that the light functions properly.
How can you disconnect the airbag alarm after that goes off periodically because the light bulb has burned out on a 2001 Taurus?
Just replace the light bulb.
How do you replace a fog light bulb on a 2001 Nissan Maxima?
This Question answered already
How do you replace bulb on high mount stop light on 2004 Chevy suburban?
if it is an LED unit you cant you have to change the assembly as a unit
How do you replace daytime running light on 2010 suburban?
To replace the daytime running light on a 2010 Chevrolet Suburban, first, open the hood and locate the headlight assembly. Remove the screws or clips securing the assembly, then carefully pull it out. Disconnect the electrical connector from the old bulb, replace it with a new bulb, and reconnect the connector. Finally, reassemble the headlight assembly and secure it back in place.
How do you replace the brake light on a 2001 Jeep Cherokee?
To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.
