0
Ford has issued a safety recall that can be directly related to the ABS modules and brake fluid leaking into the wiring harness that controls it.
Read the information at the "Related LINKS" below for much more about this recall.
Removal
Prior to removal of module, it is necessary to upload module configuration information to a scan tool equivalent to Ford's NGS,WDS, or PDS. This information needs to be downloaded into the new module once installed.
Disconnect the battery ground cable. Raise and support the vehicle. Remove the hydraulic control unit (HCU) dust shield,located directly uder the driver's door area fastened to the subframe.
Disconnect the anti-lock brake control module electrical connector. Slide the connector lock rearward.
Remove the three HCU bracket to frame bolts.
Lift the bracket hooks from the frame and lower the HCU to access the anti-lock brake module.
Be sure to lift straight up to avoid damage to the HCU components.
Remove the anti-lock brake module. Remove the bolts.
Installation
Once the new module is installed, it is necessary to download the module configuration information from the scan tool into the new module.
NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn its strategy.
NOTE: Clean the top of the HCU before installing the new module.
NOTE: Clean the harness and module sides of the electrical connector before connecting.
To install, reverse the removal procedure.
What else can I help you with?
How to Change wiper timing control module Ford Focus?
How do you change the wiper control module on a 2006 Ford Focus
Where is the constant control relay module on a 96 ford windstar 3.8?
Its beside the rad. on the drivers side
Where is the ignition control module for a 1995 ford windstar?
There is not a stand-alone ignition control module in the Windstars.Ignition control is fully handled by the Powertrain Control Moduel (PCM).See "Related Questions" below for more
Where is the airbag control module located in a 2001 Ford Windstar SE?
Airbag control module is bolted to the floor on a non-removable stand just to the right of the accelerator pedal behind the storage bay panel.
Where is the ignition module on a 1999 Ford Windstar?
If you're looking for a stand-alone ignition controlmodule, there isn't one on the Windstar.This job has been transferred to the Powertrain Control Module (PCM) and its direct control of the coilpack.
Where is the wiper control module on a 2000 ford windstar?
The wiper control module on a 2000 Ford Windstar is typically located under the dashboard, near the driver's side. It can be found mounted on the steering column or in the vicinity of the fuse box. To access it, you may need to remove some panels or covers under the dashboard. Always consult a repair manual for detailed instructions specific to your vehicle.
Where is located the sensor for the door opener on ford windstar 2002?
electronic module
How do you change transmissions in the 1995 ford Windstar?
how do you change a shaft soleniod in a ford windstar 1995 v6 3.8 engin
Where is the restraint control module located in a 2003 Ford Windstar?
In a 2003 Ford Windstar, the restraint control module is located under the center console, specifically beneath the armrest area. To access it, you typically need to remove the center console cover and possibly some fasteners. This module is crucial for the vehicle's airbag system and occupant restraint operations. Always ensure to disconnect the battery before working on any components related to the airbag system for safety.
Where is the transmission control solenoid in your 2000 ford windstar?
where is the tcm in a windstar 2000 located
How do you change the idle on a 2004 Ford Explorer?
The idle is controlled by the powertrain control module ( computer )
Where is the body control module located on a ford windstar?
The body control module (BCM) on a Ford Windstar is typically located under the dashboard on the driver's side. It is often found near the fuse box or attached to the main wiring harness. To access it, you may need to remove some trim panels or the knee bolster. Always consult the vehicle's service manual for specific instructions related to your model year.
