0
You need to remove the A pillars (the handle grips) on each side of the windshield. They are held in with 2 T25 screws.
You need to pry up the sub-straight (the 4.5 inch piece of plastic that runs along the top of the dashboard next to the windshield). Use a strong piece of plastic to pry up the sub-straight, because a metal tool might leave scratches.
At knee level, there is dark plastic dashboard trim which needs to be removed. I was able to just pull it out with my hands.
The A-lid (the plastic housing around the gauge cluster) is held in with 7 P2 Phillips head screws.
The gauge cluster is held in with 4 P2 Phillips head screws.
There is one wire connection on the back of the gauge cluster. Press the tab on the wire connector and pull it out.
With the gauge cluster free, you can turn in over. On the back of the gauge cluster you will see 9 red plastic light bulb holders. Use a 6 mm socket to loosen the light bulb holder for the burnt out bulb. Be careful to not use too much pressure with the socket wrench.
The replacement bulb I purchased from my dealer was part#4839738-AA.
My replacement bulb has a black light bulb holder, and not a red one.
It took me about 1 hour to do this.
The replacement light bulbs cost me $2.09 a piece.
What else can I help you with?
How do you get to the light bulb that lights up the speedometer so you can change it?
you have to remove the lens cover. look for screws to take it off. then the speedometer pulls out and the bulbs are behind.
How do you change the dashboard light behind the speedometer on a 2003 Chevy Silverado?
You can't you have to replace the whole dashboard instrument cluster assy.
How do you change the light bulb behind the speedometer on a 1991 jeep wrangler?
To change the light bulb behind the speedometer on a 1991 Jeep Wrangler, first, disconnect the negative battery terminal for safety. Then, remove the dashboard panel by unscrewing the necessary fasteners and gently prying it away. Once the panel is removed, locate the speedometer and detach it from the dashboard, allowing access to the bulb socket. Finally, replace the old bulb with a new one, reassemble the speedometer and dashboard, and reconnect the battery.
Why is your abs light flashing on your 1993 ford ranger and now I also have no lights on my speedometer?
If the ABS light is flashing it means the system is malfunctioning but still working. The dash light behind the speedometer is burnt out.
How do you change a light bulb in the dash of a 1972 Chevrolet pickup?
You have to reach under the dash behind the gauges and twist the rectangular knobs. There should be 2 behind the speedometer, 2 behind the rpm's, 2 for the blinkers, and 2 at the bottom of the rpm gauge. The bulbs will be in the knobs.
How do you fix a speedometer light that won't workon a 1996 ford ranger?
U HAVE TO REMOVE THE SPEEDOMETER FACE PLATE, AND REMOVE THE SPEEDOMETER AND THERE ARE ALL THE LIGHTS ON THE BACK PART OF THE SPEEDOMETER, PD:BE CAREFULL WHEN REMOVING THE SPEEDOMETER THERE IS A SPPEDO CABLE UNDER NEED U HAVE TO DISCONECT THE CABLE FROM BEHIND.
How do workers change the light bulb in the Statue of Liberty torch?
walk up the Statue of Liberty to the torch with a latter and change them
How do you change the dash light on a 1992 Toyota Corolla?
It is practically impossible to reach up behind the dash to change the bulbs. Remove the trim around the instrument panal and you should be able to pull it out enough to change the bulbs. You may have to disconnect the speedometer to get it out far enough.
How do you change a stop light bulb in a 2002 Jeep Liberty?
See the amswer for "How do you change the rear stop light bulb on a 2002 Jeep Liberty passenger side". It works.
How do you change the light behind the speedometer on a 1988 Plymouth Sundance?
you have to take the dash apart,unhook wires from the back of the panel.then unplug the bulb from the socket,and replace with new bulb,then reattatch the wires and rplace dash
How do you fix the digital speedometer light on a 1987 thunderbird?
To fix the digital speedometer light on a 1987 Thunderbird, first check the fuse related to the instrument panel, as a blown fuse can cause the light to fail. If the fuse is intact, inspect the connections to the speedometer and the circuit board for any loose or damaged wiring. Additionally, consider replacing the light bulb behind the speedometer display if applicable. If these steps don't resolve the issue, the problem might lie within the speedometer itself or the vehicle's electronic system, requiring further diagnostics.
Where is brake light switch on 2004 jeep liberty?
just behind the leg on the brake peddle
