answersLogoWhite

0

If the dryer has a button that says "Push to Start", and you push it and nothing happens, the centrifugal start switch is bad. If you can get to it, and it is an "assembled" switch (as opposed to molded or sonically welded), you can disassemble it and clean it with electrical contact cleaner (available at the large retailers). That will fix it for awhile - possible a long while. But it is not terribly expensive, and to order the factory specified replacement switch for it online is a permanent fix.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Can you bypass a centrifugal switch?

Bypassing a centrifugal switch can be dangerous as it is a safety feature designed to prevent the motor from running when not in proper operating conditions. It is not recommended to bypass the centrifugal switch as it can lead to overheating, damage to the motor, and potentially dangerous situations. If you suspect an issue with the centrifugal switch, it is best to consult a professional for repair or replacement.


What is used on a single phase induction motor to disconnect the start winding after the motor starts?

A centrifugal switch, once the motor reaches near run speed, centrifugal force causes a set of contacts to open and disconnect the start capacitors. Some larger motors use a contactor which is disconnected by the centrifugal switch.


Why can't you have a centrifugal switch inside a hermetic compressor motor?

The centrifugal switch is likely to wear out and require replacement. It could also create a spark which could cause fumes from the oil inside the motor


How can I test a dryer motor to ensure it is functioning properly?

To test a dryer motor, you can use a multimeter to check for continuity in the motor windings. You can also visually inspect the motor for any signs of damage or wear. Additionally, you can test the motor's start switch and thermal fuse for proper functioning.


Where can you get a replacement centrifugal switch for an Emerson motor?

You can try contacting Emerson directly for replacement parts, or check with authorized Emerson distributors or motor repair shops. Online retailers and marketplaces like Grainger or Amazon may also carry replacement centrifugal switches suitable for Emerson motors.


Why you cant have a centrifugal switch in a hermetic motor?

The hermetic compressor cannot use a centrifugal switch like an open motor because it will disrupt the start winding. Hermetic compressors work through insulated motor terminals, and not in the open.


How does the centrifugal switch work in a single phase electric motor?

In a single phase electric motor, the centrifugal switch allows the start winding to be energized through the start capacitor when the motor is starting. This gives an out of phase magnetic field that, along with the in phase magnetic field from the run winding, helps the rotor to begin spinning. Once the rotor reaches a certain speed, the centrifugal switch changes state and cuts off the start winding. At that point, the motor continues running only through its run winding, and inertia keeps the rotor properly phase biased relative to the run winding's magnetic field.


Why is my dryer not turning on?

There could be several reasons why your dryer is not turning on. It could be due to a faulty power source, a broken door switch, a malfunctioning thermal fuse, or a problem with the dryer's motor. It is recommended to check these components and consult a professional if needed.


What is centrifugal switch?

A centrifugal switch is an electromechanical device that is used in certain electric motors to disconnect the starting winding once the motor reaches a certain speed. This helps to improve the efficiency of the motor during normal operation by reducing power consumption in the starting winding.


What is the function of centrifugal switch in the auxiliary winding?

The centrifugal switch in an electric motor, specifically in relation to the auxiliary winding, is designed to disconnect the auxiliary winding from the power supply once the motor reaches a certain speed. This ensures that the auxiliary winding, which aids in starting the motor, is no longer needed during normal operation, preventing overheating and inefficiency. The switch operates based on centrifugal force, typically engaging or disengaging at predetermined RPMs. This mechanism helps optimize the motor's performance and longevity.


The device which disconnects the start winding in some split-phase motor circuits after a preset speed is obtained is the?

It is called a centrifugal switch. The switch is in series with the start winding. When the RPM of the motor reaches a certain speed the switch drops the start winding of the motor out of the circuit.


What is the purpose of a centrifugal switch in an automatic washer?

As the android, Data, from Star Trek would say, it's to assure the drum is operating within normal parameters. If the drum begins to spin too fast the centrifugal switch (actually two switches in unison) cuts off electrical power to the motor to prevent it running away.