0
How do you fix the turning signals and hazards on a 1999 Dodge Stratus after the fuse and lights were checked?
Sounds like the problem I just fixed on my '97 Stratus. The flasher is a combo unit for your turn signals and hazard lights. It is located on the top part of the steering column right of the hazard light swith connected to the multifunction switch (turn signal, lights and wiper switch all one unit). The unit is square and not round like most typical flashers. To remove, disconnect the negative terminal under the hood on the left shock tower first. This is to prevent you from accidently activating your airbag. Next move your tilt steering to its lowest position. Then remove the two screws on the steering column cover. Remove cover and just unplug the flasher. Unfortunately, the flasher may be only available from the dealer as it is not a common part (I've checked for days). However, mine came out of a '02 Neon at a wreakers for a quarter of the cost of new. Any Chrysler car using the same turn signal/wiper switch setup should have the part in it. The only mod you may need to do is remove some of the padding on the outside of the flasher to make it fit. .
What else can I help you with?
Turn signals not working for Acura Integra?
my turning signals dont work on my 91 integra LS. They were working a day before. so the next day they werent. I also had battery problems but i had checked every single fuse and the fuses arent burn. My turning signals do not work what so ever.
2001 dodge stratus not turning over?
jump start it.
Turning signals not working but the hazards do so what could be the problem?
I have found that moisture can cause that problem you may also want to check your fuse and bulbs if you see moisture try to get it as dry as possible
Is it illegal in Pennsylvania not to use turn signals?
The PA Motor Vehicle Code, § 3334. Turning movements and required signals- says that you will use your turn signals or hand signals when you are turning or changing lanes.
What are the common signals used by road bike riders to communicate with each other and ensure safe navigation on the road?
Common signals used by road bike riders to communicate and ensure safe navigation include hand signals for turning left, turning right, stopping, and pointing out hazards. Riders also use verbal cues such as calling out "car back" to alert others of approaching vehicles. These signals help riders communicate and stay safe while cycling on the road.
What are the different types of signals that can be used on a bicycle to indicate turning intentions?
The different types of signals that can be used on a bicycle to indicate turning intentions are hand signals and electronic signals. Hand signals involve extending the left or right arm out to indicate the direction of the turn. Electronic signals are typically found on modern bicycles and include flashing lights on the front and back of the bike to indicate turning intentions.
The turning signals work in a 1991 lebaron?
That is a good thing. You want the turn signals to work.
How do you know if you need a ignition switch for Dodge Stratus 2000?
my brother has a 2001 stratus and had problems with the ingnition switch turning forward. we hired a lock smith to repair it at a fraction of the cost.
Why does the 2001 Hyundai xg300 radio wipers and hazards turn on and off by themselves?
With my xg 300, the radio was turning on and off on it's own. I checked the battery and it was bad. Replaced it. Now it's fine again. Go to auto parts store and have your battery checked just in case. Could also be loose battery cables.
How do you turn on tUrning signals on mafia 2?
Their is no Possible way :) :(
Why Turning signals and hazards do not work?
Check all fuses first. If all of them are good, you probably have a bad multi-function switch. The only way to correct that is to replace the switch. The switch is at the end of the turn signal lever inside the steering column.
How do you find out the code on a check engine light on a 1999 dodge stratus?
On some vehicles turning the key on, off,on,off,on will make the check engine light flash the code. Three flashes, pause, three flashes would be 33 for example. If that doesn't work you will have to have it checked with a scan tool.
