answersLogoWhite

0

Open the trunk, just inside the trunk, pull down the carpet/ insulation across the rear of trunk. Look for six or eight thumb nuts. Remove all of them while holding the tail light assembly with one hand or helper. Carefully pull the whole tail light assembly out, resting it on the bumper. Cover bumper to prevent scaring. Now the wi ring/bulb sockets can be seen. Turn desired wire socket counter clockwise to removed and change bulb etc, etc. Reverse process to install. Good Luck.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Where is the fuel pump relay for a 1990 Buick Reatta located?

god only knows


What is the firing order for a 1990 Buick Reatta 3.8 L v6?

1-6-5-4-3-2


How do you replace side markers on a 1990 Buick Reatta?

I have found the easiest way to replace the sidemarker lights is actually from underneath the vehicle. I you can get the bulb out from underneath, with a squeeze and a twist, the bulb can be replaced without removing the whole assembly.


Where is the horn located on a 1991 Buick reatta?

Under the hood, at the front of a 1990 Buick Reatta, the horn is located on the driver's side, behind the fog light and mounted to the frame. If you lay down at the front of the car and look up under the fog light, you will see the horn.


Where is the fuse for dash lights located in a 1990 Buick Electra Park Avenue?

Open the drivers door and look at the side of the dashboard. This is your access to the fuse box.


Where is the low side AC connection on a 1990 Buick Reatta?

The low side AC connection on a 1990 Buick Reatta is located on the accumulator, which is situated on the passenger side near the firewall. The low side service port is typically marked with a blue cap and is used for adding refrigerant to the AC system. Always ensure the AC system is off before connecting or disconnecting the service port.


Where is the central power supply located in a 1990 Buick Riviera?

In the Reatta it is located under the dash next to the steering collum. Silver box has "central power supply" printed on it.


Is there a chilton or haynes repair manual for a 1990 Buick Reatta?

Yes, there are repair manuals available for the 1990 Buick Reatta, including both Chilton and Haynes. However, the availability of these manuals may vary, and they might not be as widely distributed as those for more common vehicles. It's advisable to check online retailers or specialty auto parts stores for physical copies or digital versions. Additionally, you might find helpful resources in forums or websites dedicated to classic Buick enthusiasts.


Spark plug firing order 1990 Buick Reatta?

The firing order for the 1990 Buick Reatta, which is equipped with a 3.8L V6 engine, is 1-6-5-4-3-2. The spark plugs are typically arranged in a way that aligns with this firing sequence to ensure proper engine performance. It's essential to follow this order when replacing spark plugs or performing ignition system maintenance to avoid engine misfires.


The firing order for a 1990 Buick Reatta schematic?

The firing order for a 1990 Buick Reatta, which is equipped with a 3.8-liter V6 engine, is 1-6-5-4-3-2. This means that the cylinders fire in that specific sequence for optimal engine performance. The cylinder layout follows a front bank of cylinders, with cylinder 1 at the front of the engine on the driver's side. Always refer to the vehicle's service manual for specific maintenance and repair information.


Where is the fuse that controls the interior lights for a 1990 Buick regal GS?

in the fuse box


How do you remove the center console cover 1990 Buick Reatta that's around the gear shift The part that holds the ash tray?

To remove the center console cover around the gear shift on a 1990 Buick Reatta, start by carefully prying off the ashtray cover to access the screws underneath. Once the screws are removed, gently lift up the console cover, being cautious of any clips or connectors. It may help to use a flathead screwdriver wrapped in cloth to avoid damaging the surrounding trim. Finally, once it's free, you can carefully disconnect any electrical connectors if present before fully removing the cover.