0
This works for a '04 4WD # Tools: slide hammer, breaker bar, 35mm socket, 10mm wrench, 15mm wrench, 15mm socket short 3/8" drive (all others 1/2" drive) # Support the truck but keep the wheels on the ground. # Remove the center cap and loosen the spindle/axle nut using the breaker bar. DO NOT REMOVE! # Loosen the wheel nuts # Raise the truck and support with jack stands # Remove the wheel. # Remove the brake caliper, but leave the brake line intact. Set the caliper in the upper suspension to keep it out of the way. # Remove the axle nut, washer and rotor. # Unplug the ABS sensor # Remove the three bolts supporting the hub rotor. The middle bolt is aggravating. Use the short 3/8" 15mm to remove this one to save time. The breaker bar is useful hear. # Use the slide hammer to remove the old hub. # Use the spindle nut to press you new hub in place. Use a hammer, ruin the bearing. After a few turns, insert the washer, and continue to install # You will have to lower the truck to tighten the spindle nut completely. # It is straight forward if you have the right tools.
What else can I help you with?
How do you install rear wheel bearings in a 2003 Corolla?
2003 Corolla rear wheel bearing sold as complete hub assembly you bolt on.
How do you replace the front wheel bearing on a 2003 Pontiac vibe GT?
Take off the steering knuckle and press out the bearing and hub.Have the new bearing pressed in with the hub and re install the knuckle.
What are the torque specs on a 2003 Malibu hub bearing?
The 2003 Malibu hub bearing torque specifications are 40 pounds per square inch. You can ruin the bearing by tightening it too much.
How do you replace wheel bearing on 2003 Pontiac vibe?
To replace the wheel bearing on a 2003 Pontiac Vibe, you'll need to lift the vehicle and remove the wheel. Next, detach the brake caliper and rotor to access the hub assembly. Remove the hub assembly bolts and use a puller to extract the old bearing. Finally, install the new bearing, reassemble the hub, and ensure everything is tightened to specifications before replacing the wheel.
How do you replace front wheel bearing on 2003 Hyundai Tiburon?
To replace the front wheel bearing on a 2003 Hyundai Tiburon, start by safely lifting the vehicle and removing the front wheel. Next, remove the brake caliper and rotor to access the hub assembly. Disconnect the hub assembly from the steering knuckle by removing the bolts, then use a bearing puller to extract the old bearing. Finally, install the new bearing, reassemble the hub, rotor, and caliper, and ensure everything is properly tightened before lowering the vehicle.
Do you have to replace the hub on a 1993 Chevy k2500 if you need to replace the wheel bearing?
If, after close inspection you do not see any damage to hub, you can use it. But ALWAYS install new bearing race with bearing.
How do you replace front wheel hub on citroen berlingo?
First, use a jack or a hoist to lift the vehicle, supporting the cars body on jack stands if not using a hoist. Remove the wheel, the bread drum or caliper, hub cap and hub nut. Remove the hub bearing using a bearing puller if required. Install the new hub bearing with grease, and re-install all parts, tightening to the manufacturer's specifications.
Install Ford Festiva wheel bearing?
Installing wheel bearing in a Ford Festiva is simple but will take some time. All you have to do is take the hub off, take out the tie rod and then take out the wheel bearing from the hub.
What size are the hub bearing bolts on a 2003 dodge durango?
7/8
What size socket for wheel bearing hub nut for an 2003 mercury mountaineer?
it is a 29 mm hub nut socket
How do you remove wheel bearing on 2003 Crown Victoria?
To remove the wheel bearing on a 2003 Crown Victoria, start by lifting the vehicle and removing the wheel and brake assembly. Next, disconnect the axle nut and remove the hub assembly, which typically involves unbolting it from the steering knuckle. Once the hub is free, you can access the wheel bearing, which may require a press to remove. Finally, install the new bearing by reversing the process, ensuring everything is properly torqued and aligned.
Tell how to change a front wheel bearing on a 1995 Plymouth Neon?
remove wheelremove cv shaft nutremove brake caliper and rotorremove bolts retaining bearing to spindleknock hub bearing out of spindle with big hammerreverse order to install new hub bearing
