0
slide radiator down into position behind the radiator support attach the air conditioning condenser to the radiator if so equipped,with force of 10Lbs to seat the radiator assembly lower rubber isolators in the mount holes provided tighten the radiator mounting screws to 9 ft. lbs. connect the automatic transaxle hoses,if so equipped,tighten the hose clamps to 35 inch lbs slide the fan shroud,fan and motor down into the clips on the lower radiator flange .install new shroud retaining clips install upper and lower radiator hoses including the coolant reserve hose plug the fan motor electrical connection and attach the negative battery cable fill the cooling system with coolant
What else can I help you with?
Where is the thermostat on a 1993 Plymouth acclaim?
It is under the housing where the upper radiator hose hooks to the engine.
How do you install a thermostat on a 1992 Plymouth acclaim?
To install a thermostat on a 1992 Plymouth Acclaim, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator and locate the thermostat housing, which is typically near the engine block. Remove the bolts securing the housing, take out the old thermostat, and clean the mating surfaces. Install the new thermostat, ensuring it’s positioned correctly, then reassemble the housing, refill the coolant, and reconnect the battery.
When was Plymouth Acclaim created?
Plymouth Acclaim was created in 1989.
Where is the thermostat located on a 1994 Plymouth acclaim?
Follow the upper radiator hose to its end. The thermostat is located right about there.
How do you remove a radiator from a Plymouth acclaim?
To remove a radiator from a Plymouth Acclaim, first ensure the engine is cool, then disconnect the negative battery cable. Drain the coolant by removing the drain plug or lower radiator hose. Next, disconnect the upper and lower radiator hoses, as well as the transmission cooler lines if applicable. Finally, remove any mounting bolts or clips securing the radiator, and carefully lift it out of the engine bay.
Does a 92 Plymouth acclaim have a radiator fan fuse?
Yes, the 1992 Plymouth Acclaim does have a radiator fan fuse. This fuse is typically located in the fuse box under the dashboard or in the engine compartment. If the radiator fan is not working, checking this fuse is a good first step to diagnose the issue. Always refer to the vehicle's owner manual for the exact location and specifications of the fuse.
93 Plymouth acclaim how do change the thermostat?
To change the thermostat on a 1993 Plymouth Acclaim, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator and remove the upper radiator hose connected to the thermostat housing. Unbolt the thermostat housing, remove the old thermostat, and clean the mating surfaces. Install the new thermostat with the spring side facing the engine, reattach the housing, and refill the coolant before reconnecting the battery.
Does the 1991 Plymouth acclaim have an interference engine?
No. A 1991 Plymouth Acclaim does not have an interference engine.
How do you replace the thermostat on a 1994 Plymouth acclaim?
To replace the thermostat on a 1994 Plymouth Acclaim, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then locate the thermostat housing, which is typically at the engine end of the upper radiator hose. Remove the bolts from the housing, take out the old thermostat, clean the mating surfaces, and install the new thermostat along with a new gasket. Reassemble the housing, refill the cooling system with coolant, and reconnect the battery.
What are the valve timing mark's for a 1994 Plymouth Acclaim?
what are the vavle timing mark's for a 1994 Plymouth acclaim
Where is the fuel pump on a 1993 Plymouth Acclaim?
The fuel pump is inside the fuel tank on a Plymouth Acclaim.
Where is the thermostat on 1991 Plymouth acclaim?
In a 1991 Plymouth Acclaim, the thermostat is located in the engine compartment, specifically at the junction of the upper radiator hose and the engine. To access it, you'll need to remove the upper radiator hose and the thermostat housing. Once the housing is removed, you can replace the thermostat. Always ensure the engine is cool before attempting to work on the cooling system.
