0
This is a FUN one! Get ready for cut up hands and a question to yourself of why you didn't pay someone to do this. Anyway, here we go... Remove the fascia that has the lock & window controls on the doorpanel. (screw & lock/window fascia snaps). Unclip window & lock switches, push out towards the front. Be careful not to break these. Remove screw for armrest, pull doorpanel off from the bottom to the top. Lift panel 'up' off of top. In the doorjamb, on the door, remove the small bolt that goes to the back of the handle (10mm). Now, there's 2 ways to go from here. One way is easier to maneuver, but involves disassembling the inner steel panel (lots of time & patience). The other way is harder, and involves snaking your arm throughout the sharp small crevaces, as well as blindly (may take as much time if you have large arms/hands). Since this may be your first time, neither way would be easy... So I'll describe the 'easier' way. Remove the clear plastic on the door, remove the screws around the inner steel panel (9/32). Remove the bolt at the bottom front of the steel panel (10mm). Carefully lift up on the steel panel, use your knee to prop it upwards. Now gently pull the steel panle back, and unsnap the 2 linkage rods from the steel panel. Use a small flat screwdriver and unclip the retaining clips at the end of each linkage. Remove linkage from power lock motor (pulls downward & slips out). Disconnect power window motor. Here's more fun.. It's better to have 3 hands for this part.... Lift off steel inner panel and turn ut to release the window regulator from the backside of the steel panel. Now, turn it some more to release the 2 rollers that goes to the bottom of the window, the window will drop. Pull out the inner steel panel Look at the backside of the door handle, and remove the 2 clips & linkages that attach to it. Remove doorhandle. Again, you will need tons of patience with this task.
What else can I help you with?
How to install Toyota Corolla Outside Drivers Door Handle?
you never gave me the answer.....
How do you install door handle 2007 Buick Rendezvous?
Inside handle, outside handle, sliding door handle?
What is the correct procedure to remove the drivers side door panel on a 2004 GMC Sierra 2500HD Crew I need to replace the outside door handle and lock?
See this document: http://www.jpcustoms.com/store/documents/signalmirrors.pdf This is actually a procedure to install some mirrors, but the process of removing the panel is shown. Jack
How do you install an outside door handle on a 1994 GMC Sierra?
you have to remove the interor door panel then take and pull up on the outside handel you will see a rod on the end of ti there is a plastic peace gently un clip the plastic peace by turning it. now there should be 2 nuts on the back of the handle remove them. and if your sierra has the option on it there will be a lock cylinder that is held on by a c clip remove that and you should be able to remove the whole handle
How do you replace the drivers side outside door handle on a 1994 Chevy lumina?
Remove the inside door panel of your 1994 Chevy Lumina. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
How do you replace the drivers door handle on a 2001 suburban?
Need to know if it is an inside or outside door handle.
How do you replace the outside door handle on the drivers side of a 2004 Silverado?
with a screwdriver
How do you replace the drivers side door handle on a 1996 GMC Sierra?
Assuming you are referring to the outer door handle, remove the inner door panel and look at the back of the handle. You will see a couple of steel rods attached to the handle, remove these(they just unclip)and move them out of your way. You should be able to see a couple of small nuts holding the handle to the door. Remove these and the handle can be pulled out of the door from the outside.
How do you replace a door handle on a Ford Fiesta?
You will need to remove the inside door panel of your Mustang. Remove the linkage from the outside door handle. Remove the outside door handle retaining bolts. Reverse the process to install the new outside door handle.
What are the buttons underneath the car door handle on the outside of the drivers side an passengers side?
its the keyless entry
How do you replace the inside drivers side door handle on a 2000 VW Beetle?
You can replace the inside drivers door handle by removing the door panel. With the door panel removed the door handle mechanism will be visible. Remove the linkage from the door handle. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
How do you install a new door handle on the outside of a 1999 Tahoe?
Remove inner door panel for access
