0
Lightly losen the lug nuts with the tires on the the ground. Jack up the car and remove the tire according to the owner's manual. Make sure to block the wheels. After the tire is removed, release the park brake. Support the car on jack stands. Remove four bolts from the rear of hub. The hub nut will be 29 mm - it is important that you have a tight fit if you attempt to remove the nut.
At this point you MAY have to loosen or remove the remove the emergency brake cable. Either way the hub is ready to be removed. The front of the hub (with the lugs) and the bearing will come out and the back plate and brake shoes will remain in place.
Once you get it off, you may either purchase a hub assembly (which includes the hub with a new bearing in place ready-to-go) or take the existing hub and a replacement bearing to an auto machine shop which can easily remove the old bearing and install the new bearing. Using extreme care you can remove the old one using bearing pullers and prybars and replace the bearing using large deep sockets or a properly sized piece of steel pipe.
Since you have the hub apart, you should inspect the brake shoes and (brake) wheel cylinders and replace them as needed. Replace brake parts on both sides if you replace them on either.
Put the hub back into the brake shoes. It may only line up one way. Finger tighten ALL FOUR of the bolts and then tighten. Replace the tire and remove the lifting equipment. Start slowly so the brakes can readjust!
What else can I help you with?
How do you replace a wheel bearing on a 2002 Tracker?
You will need to remove the tire and wheel from your 2002 Geo Tracker. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel seal and the wheel bearing. Reverse the process to install the new wheel bearing.
How do you change front axle bearing in 2002 dodge ram 1500?
Begin by removing the tire and wheel from your 2002 Dodge. Remove the end of the axle. Remove the wheel bearing nuts. Remove the wheel bearing. Reverse the process to install your new wheel bearing.
How do you wheel bearings 2002 elantra?
Changing wheel bearing from a 2002 Hyundai Elantra requires removing the hub assembly. The bearing will need to be pressed out and in to confirm and safe install.
Replace rear wheel bearing on 2002 Mercury Mountaineer?
Remove the rear tire and wheel. Remove the axle end cap. Remove the rear wheel seal. Remove the rear wheel bearing. Reverse the process to install the new wheel bearing.
How to replace Wheel Bearing on a 2002 Celica?
If it is the front bearing: Take it to a mechanic. The bearing in pressed into the spindle. A press is required to remove the old bearing and install the new one.
Grinding or rubbing sound in the front end of a 2002 Ford Focus?
A wheel bearing could be going bad in a 2002 Ford Focus if a grinding or rubbing sound is heard. A trip to a mechanic is advised as a bad wheel bearing that's not fixed can lead to damaged brakes.
How do you oil rear wheel bearing of Dodge caravan 2002?
You can't, it is a sealed wheel bearing.
How complicated to replace the rear wheel bearing on a 2002 ford focus?
Replacing the rear wheel bearing on a 2002 Ford Focus can be moderately complicated and requires some mechanical skills. The process typically involves removing the wheel, brake components, and the hub assembly to access the bearing. Special tools like a bearing puller may be necessary, and proper torque specifications must be followed during reassembly. If you're not experienced with automotive repairs, it may be best to seek help from a professional mechanic.
Does the 2002 Ford Focus have front wheel drive?
Yes , a 2002 Ford Focus is front wheel drive
Is the 2002 Ford Focus front wheel drive rear wheel drive or four wheel drive?
The 2002 Ford Focus has front wheel drive.
What is the wheel base of the 2002 Ford Focus?
The 2002 Ford Focus has a 8 ft. 7 in. (103 in.) wheel base.
How do you replace Front wheel bearing for 2002 Lexus RX300?
To replace the front wheel bearing on a 2002 Lexus RX300, start by safely lifting the vehicle and removing the front wheel. Next, detach the brake caliper and rotor to access the hub assembly. Remove the hub assembly by unbolting it from the steering knuckle, and then use a bearing puller to extract the old bearing. Install the new bearing into the hub, reassemble the hub with the knuckle, and reattach the caliper and rotor before putting the wheel back on. Always ensure all components are torqued to the manufacturer's specifications.
