I presume you mean the outside track. Most likely, due to the year of your vehicle, your roller bearings are worn out to the point of no longer being able to stay in the track. Get a new set of bearings. Remove the trim covers inside the van where the track runs outside. Remove the right tail light assymbly and the rubber plug you will find behind the tail light. Remove the bolt under the rubber cap. Remove the bolts to the track cover found under the inside trim panels. Remove the bolt at the door latch area that holds the track cover. Remove the track cover, do not force it, just find the bolt you missed.
There are a couple of ways to proceed. I reccommend removing the circlip and driving out the pin that holds the bearing assymbly to the sliding door. Replace the worn bearings and lubricate as needed. Take the bearing assymbly to the rear of the vehicle at the track end and insert the bearing assymbly into the track and run it along the track to the door, then pin it back into the door (a helper, a jack, or any type of door support is useful here). Slide the door along the track to detect ease of operation or other problems. Reinstall track cover, tail light, and interior trim panels.
FYI, some of the interior bolts and the roller assymbly pin are difficult to get to but not impossible. Plug any hole an interior bolt could fall into during removal and installation, have a wobble extension, a magnetic part retriever, spare circlips, and/or spare bolts handy. You might want to use a hole cutter to get to one of the interior bolts.
To remove a sliding door from its track, first lift the door slightly to release it from the track. Then, tilt the bottom of the door towards you and lift it out of the track. Be sure to have someone help you if the door is heavy to avoid injury.
You need to replace the guide roller located on the lower portion of the door. The plastic roller probably dried out and broke off.
To replace a sliding door track effectively and efficiently, follow these steps: Remove the old track by unscrewing it from the door frame. Measure the length and width of the track to ensure you purchase the correct replacement. Install the new track by screwing it into the door frame, making sure it is level. Test the sliding door to ensure it moves smoothly along the new track.
To install a sliding farmhouse door in your home, you will need to measure the door opening, purchase a sliding door kit, attach the track to the wall above the door frame, hang the door on the track, and make any necessary adjustments for smooth operation.
A diagram of the sliding side door on a 1999 Chevy Astro Van can be seenÊin the service manual. This manual is available from the manufacturer upon request.
To remove a sliding door from its tracks, first lift the door slightly to release it from the bottom track. Then tilt the bottom of the door towards you and lift it out of the top track. Be sure to have someone help you if the door is heavy.
To install a hanging sliding door in your home, you will need to measure the door opening, purchase a sliding door kit, attach the track to the top of the doorway, hang the door panels on the track, and adjust the door for smooth operation. Follow the manufacturer's instructions carefully for proper installation.
To put a sliding screen door back on track, first lift the door and align the wheels with the track. Then gently lower the door back onto the track and slide it back and forth to ensure it moves smoothly. If needed, adjust the wheels or track to ensure proper alignment.
A sliding door floor guide is used to keep the bottom of a sliding door aligned and stable as it moves along the track. This helps prevent the door from swinging or wobbling, ensuring smooth and consistent operation of the sliding door.
To fix a sliding door track, first clean the track and remove any debris. Then, adjust the track alignment by loosening the screws and repositioning it. Lubricate the track with silicone spray or a similar lubricant. If the track is damaged, consider replacing it with a new one.
To fix a sliding door track that is not functioning properly, you can try cleaning the track to remove any debris or obstructions. You can also lubricate the track with a silicone-based lubricant to help the door slide smoothly. If these steps do not work, you may need to adjust the alignment of the door or replace the track if it is damaged.
To install a sliding door, first measure the opening and purchase a door that fits. Remove the existing door and frame, then install the new track and frame according to the manufacturer's instructions. Hang the door on the track and adjust as needed for smooth operation.