0
1.disconnect the negative ground from the battery
2.If it has a column shift disconnect the link rod by prying out the grommet in the shift lever
3.Remove the steering shaft lower coupling to the wormshaft roll pin
4.Disconnect the wiring connectors at the steering column jacket
5.Remove the steering wheel center pad assembly
6.Disconnect the horn wire and remove the horn switch
7. Remove the steering wheel retaining nut. DO NOT HAMMER ON THE STEERING SHAFT TO REMOVE THE STEERING WHEEL.
8. Remove the turn signal lever
9. Remove the floor plate to the floor pan attaching screws
10. To expose the steering column bracket, remove the cluster bezel and panel lower reinforcement
11. Disconnect the automatic shift indicator pointer cable from the shift housing
12. Remove the nuts attaching the steering column bracket to the instrument panel support
13. Carefully remove the lower coupling from the steering gear wormshaft, then remove the column assembly out through the passenger compartment
What else can I help you with?
How do you remove the ignition switch tumbler on a 1986 dodge lancer 2.5?
Remove the screws on the side of the steering column. Remove the screws underneath the steering column and pull the bottom half of the column down. Slide a pin punch into the hole at the ignition tumbler assembly's bottom. Force the tumbler upwards and pull it out of the steering column.
How do you remove the steering column in a 1986 Chevy Celebrity?
To remove the steering column in a 1986 Chevy Celebrity: 1. Remove the trim panel under the steering column. 2. Remove the noise panel. 3. If the car has column shift remove the gear indicator from the shift bowl. 4. Unplug electrical connectors. 5. Remove the four bolts that hold the steering column up. 6. At this point the steering column should pull out.
How do you remove the ignition switch from the steering column on a jeep grand wagoneer 1986?
To remove the ignition switch from the steering column of a 1986 Jeep Grand Wagoneer, first disconnect the battery to ensure safety. Then, remove the steering column cover by unscrewing the retaining screws. Next, locate the ignition switch, disconnect the electrical connectors, and remove any screws or bolts securing it in place. Finally, pull the ignition switch out from the column to complete the removal.
How do you replace wiper switch in steering column 1986 Toyota?
First you have to remove the cover on the steering column. Then locate the mounting screw for the switch. When installing the new switch make sure the alignment is correct.
How do you replace steering column on 1986 Pontiac parisienne?
how to change steering column on 86 pontiac bonneville
Where is the fuse box for a 1986 Mercury Marquis mid-size?
remove plastic cover under steering column. It is held on with screws.
How do you replace ignition switch on a 1986 Chevy silverado?
To replace the ignition switch on a 1986 Chevy Silverado, first disconnect the battery to prevent any electrical issues. Remove the steering column cover by unscrewing it, then locate the ignition switch, which is typically mounted on the steering column. Disconnect the wiring harness from the old switch, remove the mounting screws, and replace it with the new ignition switch. Reassemble the steering column cover, reconnect the battery, and test the new switch to ensure it functions properly.
How do you remove steering column from a 1986 ford f250 ton truck?
Sorry I don't have any specifics for you, but look for the Ford Light Truck Shop Manual for 1986 (eBay has 'em for $30).
How do you change an ignition switch on an 1986 ford e350?
To change the ignition switch on a 1986 Ford E350, first disconnect the negative battery cable to prevent any electrical shorts. Then, remove the steering column covers and locate the ignition switch, which is typically mounted on the column. Disconnect the wiring harness from the switch and unbolt it from the column. Finally, install the new switch, reconnect the wiring, and reassemble the steering column covers.
How do you replace ignition switch on 1986 camaro?
Remove the dress plate under the steering column. There is a clip there for the shift indicator, if you shift on the column. There are two nuts on studs, one on each side of the column, remove these nuts, and the steering column will drop down. The switch is on top of the column just lower then the fastening bracket. Unplug the wiring, remove the screws that retain the switch, install new one and adjust. Put everything back together.
How do you remove the ignition switch in a 1986 El Camino?
To remove the ignition switch in a 1986 El Camino, first disconnect the battery to ensure safety. Then, remove the steering column cover by unscrewing the screws securing it in place. Next, locate the ignition switch, disconnect the wiring harness, and remove the mounting screws or bolts securing the switch to the column. Finally, pull the switch out to complete the removal.
Where is the ignition switch located on an 1986 Cadillac Seville?
In a 1986 Cadillac Seville, the ignition switch is typically located on the steering column. To access it, you may need to remove the steering column cover. The switch is connected to the ignition lock cylinder, which is where you insert the key to start the vehicle. Always refer to the vehicle's service manual for specific instructions and safety precautions.
