0
I took high resolution pictures of each step., too bad ther is not a way to post those pictures
This car has only the turn signal and headlight bulbs (total of two bulbs) in the headlight assembly.
Raise the hood and locate the two 7mm bolt heads on the chassis frame just above and the left and right edges of the headlight (called HL in the rest of this description) assembly. The left bolt is rather long; the right bolt is what you would expect. You can tell that you identified the correct bolts after loosening the left bolt; the HL assembly will move slightly when wiggled.
After removing both bolts (be sure to note which bolt goes back into which hole) the HL assembly takes a little effort to break the weather tight seal with the car chassis. Apply enough pressure and twisting action to break it loose without ripping it out of the enclosure, the electrical cables are short.
You now have the HL assembly in your hand and need to reach into the space allowed to twist off the locking ring where the electric cable joins the bulb. This is also a rather strong twist clockwise as you face the car. Once you spin it off, slide the locking ring back over the cable away from the bulb.
Now you need to break the seal between the body and the HL assembly. Once again it takes more pressure than you would expect. Rock the bulb/cable until it breaks loose and comes away from the HL assembly. Be careful, the HL assembly is still attached to the car via the electrical cable.
Next you need to get the bulb away from the electrical cable. There is a locking device that you need to gently lift away from the bulb housing. This almost takes three hands because the locking device has two pieces; be careful not to snap this off. I used a screwdriver to lift both sides of the locking device while pushing with my thumb against the socket at the end of the cable.
Once the old bulb is out of the socket carefully push the new bulb into the socket/cable without touching the glass portion of the bulb. Push the bulb back into the HL assembly, there is no correct orientation (no up or down or left/right), just push it in without touching the glass portion of the bulb. Then work the locking ring back over the bulb/cable assembly and twist it onto the HL assembly until it snaps into place.
Work the HL assembly back into the chassis with delicate twisting and pushing motion until it too snaps into place. Insert and tighten the bolts (left is long) and get gone. Don't over tighten those bolts.
What else can I help you with?
How do you change the headlight assembly on 2004 s60?
Begin by removing the wiring harness from the back of 2004 Volvo headlight. Remove the headlight assembly retaining bolts. Reverse the process to install your new headlight assembly.
How do you remove the headlight assembly from a 2004 Mazda mpv?
how remove headligth lenses for 2004 Mazda mpv
How do you remove a headlight from a 2004 xj8?
To remove a headlight from a 2004 Jaguar XJ8, first, open the hood and locate the headlight assembly. Unscrew any retaining screws or bolts securing the assembly, then gently pull the headlight forward to release it from the clips. Disconnect the electrical connector at the back of the headlight, and finally, remove the headlight from the vehicle. Be sure to handle the assembly carefully to avoid damage.
How do you remove headlight assembly from a 2004 Mitsubishi outlandert?
To remove the headlight assembly from a 2004 Mitsubishi Outlander, first, open the hood and disconnect the negative battery cable for safety. Next, locate and remove the screws or bolts securing the headlight assembly, typically found at the top and side of the assembly. Carefully pull the assembly out, disconnect the electrical connectors, and remove any additional clips or fasteners. Once everything is detached, you can fully remove the headlight assembly from the vehicle.
How do you remove headlight assembly from a 2004 buick rendezvous?
To remove the headlight assembly from a 2004 Buick Rendezvous, start by disconnecting the negative battery cable for safety. Next, open the hood and locate the headlight assembly; remove the screws or bolts securing it in place. After that, carefully pull the assembly forward and disconnect the wiring harness. Finally, you can lift the assembly out of the vehicle.
How do you remove headlight 2004 F350?
To remove the headlight from a 2004 Ford F-350, start by opening the hood and locating the headlight assembly. Remove the retaining clips or screws that hold the assembly in place, usually found at the top and side of the headlight. Once the screws or clips are removed, gently pull the headlight assembly forward and disconnect the electrical connector. Finally, replace the headlight bulb if needed, and reverse the process to reinstall the assembly.
How do you remove the head lamp cover assembly on a 2004 Mitsubishi gallant?
the glass cover on the headlight is not servicable, they are glued during assembly. you have to replace the entire headlight globe or headlight assembly.
How do you remove the headlight assembly from a 2004 Honda Pilot?
To remove the headlight assembly from a 2004 Honda Pilot, first, open the hood and locate the screws securing the headlight assembly. Remove these screws, typically found at the top and side of the assembly. Next, gently pull the assembly forward to disconnect it from the clips, and unplug the electrical connector from the back. Finally, take out the assembly completely for replacement or repair.
How do you remove a 2004 Mitsubishi endeavor headlight assembly?
To remove the headlight assembly from a 2004 Mitsubishi Endeavor, first, open the hood and locate the headlight assembly. Remove the retaining screws or bolts securing the assembly, usually found at the top and side of the unit. Disconnect the electrical connector by pressing the tab and pulling it out, then gently pull the headlight assembly forward to detach it from the vehicle. Be sure to handle the assembly carefully to avoid damaging any clips or brackets.
Where is the horn on a 2004 Dodge Neon?
Under the passenger side headlight assembly, you have to remove the entire assembly to get to it.
How do you change a headlight bulb on a 2004 Chrysler Sebring?
you'll need Allen wrenches. you must pop the hood and remove the headlight assembly. if I remember correctly, there are about four Allen screws to take out. once it is out, you just unplug the old bulb and plug in the new.
How do you remove headlight on 2004 Cadillac CTS?
To remove the headlight on a 2004 Cadillac CTS, first, ensure the vehicle is turned off and the keys are removed. Open the hood and locate the headlight assembly, then remove the two screws securing it in place. After unscrewing, gently pull the headlight assembly forward and disconnect the electrical connector by pressing the tab and pulling it off. Finally, you can replace the headlight bulb or the entire assembly as needed.
