0
I have (2) 2001 Azteks, and have had to do this on both of them. It doesn't have an "SIR Fuse," so I disconnected the battery. I would also recommend buying a genuine AC Delco switch (dealer) and not a remanufactured or "cheap" new one. Made that mistake the first time (cheap new one) and had to replace it shortly after. The "genuine" AC Delco has lasted me 75,000 miles (mine has 203,000 miles on it, the wifes has 154,000 miles). You do get what you pay for in some instances!
Turn wheels to straight ahead position, and then make sure ignition is off.
Remove negative battery cable.
Disable SIR (air bag system) by unhooking the wiring harness to the drivers side (located beneath the dash, you'll have to remove a cover, it should be a yellow connector). The passenger side connector is underneath the seat, same style, same color.
IF you have side impact bags, locate those connectors and unhook them also.
On the underside of the steering wheel, there is a trim cover. You will need a #2 Phillips screwdriver and a torx bit (can't remember which size) to remove the trimcover.
Once you've removed the screws, remove the cover. The Ignition Switch is directly below the ignition lock cylinder. You will need two flatblade screwdrivers.
Depress (at the same time) both retaining screws, the switch will be able to be slid down and out.
Unhook harness, install switch, and replace trim covers.
To arm the SIR system, reconnect harnesses.
Reconnect negative battery cable.
What else can I help you with?
How do you remove ignition switch cover on an Pontiac Aztek?
On my 2001 Aztek, I could pull the key out when driving. To change the ignition without removing the steering wheel, take the two screws out from underneath the covering behind the wheel. Not the screws on the steering wheel. The cover will lift up but won't come off. Take an Alleen wrench and feel for the hole on top of the ignition (it will be a tight squeeze), and push in. I should also say remove the black or gray cover on the ignition switch (where the key goes in). Once you find the hole and push down on it, the ignition switch will come out.
How to remove ignition switch 1984 Chevy Caprice?
How to remove ignition switch
How do you change ignition lock on 2002 Pontiac aztek?
To change the ignition lock on a 2002 Pontiac Aztek, start by disconnecting the negative battery cable for safety. Remove the steering column covers and then access the ignition switch by unscrewing it from the column. Use a key to turn the ignition to the "Accessory" position, which will allow you to press the release tab and remove the old lock cylinder. Finally, insert the new ignition lock cylinder, reassemble the steering column covers, and reconnect the battery.
How do you replace ignition switch on a 2000 silverado?
Remove the ignition switch retaining ring. Pull the ignition switch out. Remove the wiring harness from the back of the ignition switch. Reverse the process to install the new ignition switch.
How do you remove the ignition switch on a 1989 Chevy Corvette?
Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.
Instructions on how to remove ignition switch on a 1990 Lexus LS400?
Remove the retaining ring from the top of your 1990 Lexus ignition switch. The ignition switch will slide out. Remove the wiring harness.
How do you remove new beetle ignition switch?
the question is, how don't you remove new beetle ignition switch?
How do you remove the ignition switch on a 08 Kia Optima?
how do you remove an ignition switch from an 07 kia optima
How do you remove the ignition switch on a 1999 Chevy Cavalier?
Remove the retaining ring from the top of your 1999 Chevy Cavalier ignition switch. Slide the ignition switch out and remove the wiring harness from the end of it.
How do you replace the ignition switch on Lexus es300?
remove ignition switch 92es300
How do you replace the ignition switch on a '92 Plymouth Colt?
The 1992 Plymouth Cold ignition switch is held in place by a retaining ring. Remove the retaining ring at the top of the ignition switch. Pull the ignition switch out. Remove the wiring harness from the ignition switch. Reverse the process to install the new ignition switch.
How do you change ignition switch in a 98 ford explorer?
Remove the retaining nut from the ignition switch. Pull the switch out and remove the wiring harness. Reverse the process to install the new ignition switch.
