0
you have to remove the steering wheel then using a lock plate removal tool depress the lock plate and removed the clip that holds it in place then remove the lock plate then remove the screws from the turn signal switch and pull it up slightly then remove the screw that hold the lock cylinder in place then remove the lock assembly
What else can I help you with?
Where is ignition switch located on 2000 Pontiac Montana?
On the 2000 Pontiac Montana, the ignition switch is located on the steering column, behind the steering wheel. To access it, you typically need to remove the lower steering column cover. This switch is connected to the ignition lock cylinder, allowing you to start the vehicle when the key is turned.
How do you remove ignition switch 1970 Pontiac gto?
To remove the ignition switch from a 1970 Pontiac GTO, first disconnect the battery to ensure safety. Then, remove the steering column cover by taking out the screws or bolts securing it. Locate the ignition switch, disconnect the wiring harness, and unscrew the switch from its mounting position. Finally, pull the switch out carefully from the steering column.
How do you change ignition lock on 2002 Pontiac aztek?
To change the ignition lock on a 2002 Pontiac Aztek, start by disconnecting the negative battery cable for safety. Remove the steering column covers and then access the ignition switch by unscrewing it from the column. Use a key to turn the ignition to the "Accessory" position, which will allow you to press the release tab and remove the old lock cylinder. Finally, insert the new ignition lock cylinder, reassemble the steering column covers, and reconnect the battery.
How do you remove ignition switch from a 1970 Chevelle steering column?
To remove the ignition switch from a 1970 Chevelle steering column, first ensure the battery is disconnected for safety. Then, remove the steering wheel, and disassemble the column cover to access the ignition switch. Locate the switch at the base of the column, disconnect the wiring harness, and remove any screws or bolts securing the switch in place. Finally, carefully pull the ignition switch out of the column.
How do you replace the ignition on a 1993 Pontiac sunbird?
To replace the ignition on a 1993 Pontiac Sunbird, first disconnect the negative battery cable to ensure safety. Remove the steering column covers to access the ignition switch, then detach the wiring harness and unscrew the ignition switch from the column. Install the new ignition switch by reversing the process, securing it in place, reconnecting the wiring harness, and replacing the steering column covers. Finally, reconnect the battery and test the ignition to ensure it works properly.
How do you remove the ignition key switch on a 94 probe?
Disconnect the negative battery cable. Remove steering column covers Disconnect the electrical connector from the ignition switch Remove the screw retaining the switch to the steering column
How do you remove a ignition from a steering column on a 1988 ford bronco?
To remove the ignition switch from the steering column of a 1988 Ford Bronco, first disconnect the battery to prevent any electrical issues. Next, remove the steering wheel and the steering column cover to access the ignition assembly. Locate the ignition lock cylinder release pin, insert a small tool to press it, and turn the key to the "run" position to pull out the ignition cylinder. After that, you can detach the ignition switch from the column by removing any retaining screws or clips.
How do you remove the ignition switch tumbler on a 1986 dodge lancer 2.5?
Remove the screws on the side of the steering column. Remove the screws underneath the steering column and pull the bottom half of the column down. Slide a pin punch into the hole at the ignition tumbler assembly's bottom. Force the tumbler upwards and pull it out of the steering column.
How do you remove the ignition switch from the steering column on a jeep grand wagoneer 1986?
To remove the ignition switch from the steering column of a 1986 Jeep Grand Wagoneer, first disconnect the battery to ensure safety. Then, remove the steering column cover by unscrewing the retaining screws. Next, locate the ignition switch, disconnect the electrical connectors, and remove any screws or bolts securing it in place. Finally, pull the ignition switch out from the column to complete the removal.
How do you remove the steering column bearings on a 1994 ford F350?
remove column dust covers, along with ignition switch. then remove retaining
How do you remove ignition barrel from bf xr8?
how to remove key barrel from a XR8 steering column
What is a interlock relay and what does it corvette74 and how can you remove your ignition from your steering column?
the hole steering colom needs to be replaced
