answersLogoWhite

0

I usually have to use a large pair of channel locks to get it loose. The key operative word is GENTLY apply enough pressure to grip but not too much to risk breaking the cap. I have a 91 Wrangler & this works for me.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you change a clutch master cylinder on a 1994 Toyota Corolla?

Remove clutch cable connection and then remove slave cylinder line from master. Then unbolt slave master and remove it. Follow same procedure in reverse order.


How do you replace the clutch master cylinder on a 1991 jeep wrangler?

ON my 94 you have to drive out the pin that holds the hydaulic fluid line to the master cylnider. I did this with a punch and a hammer. Then remove the pin holding the cylinder to the top of the clutch pedal (in the floor board) . Then simply remove the 2 1/2 inch nuts holding it to the firewall. Took me about 30 min.


How do you replace a clutch master cylinder in a 1995 Mazda mx-6?

To replace the clutch master cylinder in a 1995 Mazda MX-6, first, disconnect the negative battery terminal to ensure safety. Remove the clutch fluid reservoir cap and drain the fluid, then detach the hydraulic lines from the master cylinder. Unbolt the master cylinder from the firewall and remove it, then install the new master cylinder by reversing the removal steps. Finally, refill the reservoir with brake fluid and bleed the clutch system to remove any air.


How do you replace clutch master cylinder for a Ford Probe 94'?

To replace the clutch master cylinder on a 1994 Ford Probe, first, disconnect the battery and remove the engine cover if applicable. Next, locate the clutch master cylinder on the driver's side, disconnect the hydraulic line and remove the retaining bolts. Install the new master cylinder by securing it with the bolts, reconnect the hydraulic line, and bleed the clutch system to remove any air. Finally, reconnect the battery and test the clutch operation.


What if your clutch on your 85 Toyota corolla goes to the floor and is hard to shift?

There are two normal causes. The clutch is worn out or there is a leak in the hydraulic clutch slave or master cylinder. To check the clutch, press the clutch slave cylinder down. If the clutch slave cylinder bellows compresses down to the slave cylinder, the clutch is worn out. Check the clutch master cylinder fluid level. if this is low, then the clutch cylinder need to be checked. To check for a hydraulic leak in the clutch slave cylinder, remove the cylinder's bellows and check for any fluid. If fluid is present, rebuild or replace the cylinder and bleed the system. To check the clutch master cylinder, check the back the of clutch master cylinder for leaks. If fluid is present, replace or rebuild clutch master cylinder and bleed the system. In my experience, hydraulic leaks occur at the clutch slave cylinder.


How do you replace a clutch slave cylinder on a 1991 YJ Wrangler?

You will have to remove the transmission since the slave cylinder on the 91 yj is inside the bellhousing.


How do you replace a 1993 Camaro clutch master cylinder?

the master clutch cylinder , losen bolt inside fire wall to the end do not remove nuts at this time , attatach wire to it and lower it to the ground


Where is the clutch master cylinder situated and how do you remove it?

Make of vehicle would help, but almost all clutch master cylinders are beside the brake master cylinder on the drivers side of the engine compartment on the firewall. The clutch is the one closer to the center of the car. There will be a pin on the inside that connects the rod in the master cylinder to the clutch pedal and two or four bolts holding it to the firewall.


What is wrong with your clutch system if you just changed the clutch master cylinder and slave cylinder and your clutch pedal wont engage the slave cylinder?

If you allowed the master/reservoir to drain empty while the line was disconnected or installed the master dry, you may have to remove the master and bench bleed it first. Always keep the reservoir full during the process.


How do you replace the clutch master cylinder on a 1993 Toyota Paseo?

To replace the clutch master cylinder on a 1993 Toyota Paseo, first, disconnect the negative battery terminal and remove the clutch fluid reservoir cap. Then, detach the hydraulic lines from the master cylinder and unbolt it from the firewall. Install the new master cylinder by reversing the removal process, ensuring all connections are secure and refilling the reservoir with the appropriate fluid. Finally, bleed the clutch system to remove any air before testing the clutch operation.


What steps do you take to remove and replace the master clutch cylinder of a 1992 Ford Ranger?

If you need to replace the slave cylinder it is located in the bell housing and the trans has to be removed. The clutch master cylinder is located on the firewall on the drivers side


How do you remove the clutch master cylinder f250 7.3 super duty diesel?

To remove the clutch master cylinder on a 1999-2003 Ford F250 7.3 Super Duty Diesel, first, disconnect the negative battery cable. Then, remove the clutch fluid reservoir cap and disconnect the hydraulic line from the master cylinder. Next, unbolt the master cylinder from the firewall and carefully pull it out, ensuring to minimize fluid spillage. Finally, install the new master cylinder by reversing the removal steps, making sure to bleed the system of air afterward.