0
Far as i know you have to remove the over head lights in the console and there should be screws in the roof holding the Overhead Console!! if not let me know i will dismantle one and let you know...
AnswerThese vary from year to year, I have an 02 and have not been able to get a straight answer on console removal myself. I am trying to replace light bulbs in the console. The 02 has a single screw in the rear portion when you open the Eyeglass holder (A drop down door). One site said to remove that screw and just pull down, the entire housing will then "pop" out. I tried this and after putting quite a bit of downward force I stopped in fear of breaking something, it simply didn't feel right, was sure something would break. AnswerYou're right about removing the screw under the glasses door and pulling down. There are two clips about 4" in front of the screw and it takes quite a bit of pull to release them but make sure you pull from the rear of the console because the front is inserted into the headliner frame so the console pivots down hinging on the front after the screw and two clips are released. It helps to release one side at a time.================================================================================================================================
The advice to remove the screw under the glasses door and pulling down firmly was a big help to me. Here's some additional info that may be helpful. I have a 2007 T&C, basic, bottom -of-the-line model. Bought it used. The lamps had melted the plastic so I could not replace the bulbs. Had to replace what Chrysler calls the "module Bulb," to the tune of $87 and tax. Step 1: disconnect the battery. 2. remove the screw under the glasses door. 3. The clips are about 6 1/2 inches from the rear of the console. As you pull down firmly to release the clips, you may be able to use a putty knife to help release the clip. 4. To remove the black electric connection plug on the right rear of the console, insert a very thin screwdriver at the top of the connector to push down the small plastic retainer clip; then pull out the plug. 5. To disconnect the wire connector plug on the left front of the console, use a small screwdriver to push up on the retainer clip that is on the bottom of the plug. 6. Use a T10 bit to remove the ten screws in the build module. It's very helpful to have someone help when you are removing the electrical connectors.
What else can I help you with?
Remove the overhead console on s-10 blazer?
how to I remove the overhead console on the S 10 Blazer?
How can you remove the Overhead console in a 2007 dodge ram?
To remove the overhead console you will first need to disconnect and isolate the negative battery cable. Remove the overhead screws and pull straight down on the console.
How do you change the map lights in a 1999 Chrysler LHS?
remove the screw near the front of the overhead console. Using a trim removel tool, gently pry the unit away from the headliner on the left and right side of the overhead console.
Camry overhead console removal?
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
How do you remove Tahoe overhead console?
You will need to remove the headliner. With the headliner removed you will be able to see the overhead console retaining screws. Remove the retaining screws.
What are the wiring connections for the overhead console of a 1999 Dodge Durango?
The 1999 Dodge Durango overhead console wiring connections are beneath the overhead console. You will need to remove the overhead console?æin order to access the wiring connections.
How do you disassemble overhead console in 94 Chevy Suburban?
Remove the screws that hold the headliner in place. With the headliner removed the overhead console retaining bolts will be visible. Remove the retaining bolts. Remove the wiring harness from the console.
How do you remove overhead console with sunroof 2007 grand caravan sxt?
To remove the overhead console in a 2007 Grand Caravan SXT with a sunroof, start by carefully prying off any plastic covers around the console to expose the screws. Remove the screws using a screwdriver, then gently pull the console down to disconnect any wiring harnesses attached to it. Make sure to support the console as you detach it to avoid damaging any clips or connectors. Finally, once everything is disconnected, you can fully remove the overhead console.
How do you remove the overhead console base?
To remove the overhead console base, start by gently prying off any trim pieces or covers that may be concealing screws or clips. Next, locate and remove the screws securing the console base to the ceiling. Carefully pull down on the console to detach it from any remaining clips or connectors, ensuring not to damage any wiring. Finally, disconnect any electrical connectors if applicable, and the overhead console base should be free.
How do you get under shift console in 2007 chrysler sebring to press transmission rance sensor to get out of park?
Remove the bolts holding the console down and remove.
How does one remove front overhead console on a 2011 Toyota Sienna?
To remove the front overhead console on a 2011 Toyota Sienna, start by carefully prying off the plastic covers on each side using a flat tool to access the screws. Unscrew the two screws holding the console in place, then gently pull the console down to disconnect any wiring harnesses. Once disconnected, you can fully remove the overhead console. Always ensure to handle the components with care to avoid damage.
Where the airbag control module 2005 Chrysler 300?
Remove the center console. The module will be in front of console under dash
