0
Raise wagon rear door hatch open. Grasp from the top edge the plastic molding around the glass and pull, but don't pull completely away. Be careful around the wiper motor housing and the pigtail for the window defrost. On the metal part of the window frame is a rubber plug in the center, pop this out to loosen and remove the top 10mm nut. The remaining(3) 10mm nuts are accessed thru openings in the metal window frame once the plastic molding is pulled back. Once you have all(4) nuts removed carefully push but don't connect plastic molding back towards frame so that you can lower and and close the rear hatch. Now you can remove the 3rd brake light housing from the outside and twist and remove light socket plug ins. Most Ford's use a L22 bulb. Double check your work, then install and tighten (4) 10mm nuts. To reinstall, be careful with the metal molding clips, notice one tongue goes up and the next clip the tongue goes down. Just massage the plastic window molding back into place using gentle up and down motion, make sure all (4) metal clips are secure.
What else can I help you with?
How do you change the high mount brake lite on a 2007 Taurus?
The way that you change a high mount brake light on a 2007 Taurus is by first prying the light assembly from the housing. You then push rearward to remove it from the retaining clips. Next, life the light assembly from the shelf and disconnect the assembly wiring. Replace the light assembly and reverse directions to put the light housing back where it goes.
How do you replace brake light on Lexus RX300?
The brake light assembly can be access through the cargo compartment. Remove the cover to the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. The brake light will come out. Reverse the process to install the new brake light.
How do you replace brake light on Citroen c1?
To replace the brake light on a Citroen C1, first, open the rear hatch and locate the brake light assembly. Remove the screws or clips securing the assembly and carefully pull it out. Disconnect the electrical connector and twist the old bulb counterclockwise to remove it. Insert the new bulb, reconnect the electrical connector, and reassemble the brake light assembly.
How do you change a high mount center brake light on 2001 Ford Taurus wagon?
To change the high mount center brake light on a 2001 Ford Taurus wagon, first, open the rear hatch and locate the two screws or clips securing the light assembly. Remove these screws or clips and gently pull the assembly out from the rear of the vehicle. Disconnect the wiring harness, replace the old bulb with a new one, then reconnect the harness and reassemble the light by securing it back in place with the screws or clips. Finally, test the brake light to ensure it is functioning properly.
Center brake light replacement 2001 corolla?
The center brake light replacement will require replacing the entire brake light assembly. Remove the wiring harness. Remove the center brake light retaining screws. Reverse the process to install the new center brake light.
How do you remove brake light 1998 slk 230 Mercedes?
To remove the brake light on a 1998 Mercedes SLK 230, first open the trunk and locate the light assembly. Remove the screws or clips securing the assembly, then gently pull it out from the body of the car. Disconnect the wiring harness from the back of the light assembly and replace the bulb if needed. Finally, reinstall the assembly by reversing the process.
How do you remove third brake light s10?
Remove the two screws in the lens. You can remove the entire assembly once you do this.
How do you change a 2006 Acura brake light?
To change the brake light on a 2006 Acura, first, open the trunk and locate the tail light assembly. Remove the screws or clips securing the assembly, then gently pull the assembly out from the vehicle. Disconnect the electrical connector and twist the brake light bulb counterclockwise to remove it. Replace it with a new bulb, reconnect everything, and reattach the assembly to finish the job.
How do you replace bulb on brake light Toyota Highlander?
To replace the brake light bulb on a Toyota Highlander, first, open the rear hatch and locate the brake light assembly. Remove the screws or clips securing the assembly, then gently pull it out. Disconnect the wiring harness and remove the old bulb by twisting it counterclockwise. Insert the new bulb, reconnect the harness, and reassemble the brake light assembly.
How do you replace or change the third brake light on a 2007 Ford Taurus?
To replace the third brake light on a 2007 Ford Taurus, start by opening the trunk and removing the access panel located in the rear trim. Disconnect the wiring harness from the old light assembly and remove the screws or clips securing it in place. Replace it with the new light assembly, reconnect the wiring harness, and secure it with screws or clips before reattaching the access panel. Test the new light to ensure it's functioning properly.
How you you change the high mount brake light on 2001 Lexus RX300?
Remove the wiring harness from the high mount brake light. Remove the back cover of the brake light assembly. Take hold of the brake light connector, push in and turn at the same time. Reverse the process to install the new brake light.
How do you replace the brake light on a 2001 Jeep Cherokee?
To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.
