0
Remarkably easy. get inside and push the rubber gasket out around the edges with your fingers (easiest when it's more than 70 degrees fahrenheit) - it may take a bit of prying with a small flat-head screwdriver to get the very first of it to start pushing through, but once you get started it works around easily with fingers. After pushing the windsheld out, carefully remove the gasket from the old one to avoid damaging it, unless you do not plan to re-use gasket. If you are re-using the gasket, clean the inner and outer grooves of it with a mild gentle soapy water and then install it around the outside of the new windshield. Now, find a long piece of small cotton string just big enough to fit in the groove around the windshield gasket and get some Elmers Glue or equivalent all purpose nontoxic water soluable glue. Mix the glue half-and-half with water, soak the string in it, and then push the string down into the outer groove all the way around the windshield gasket. Leave the 2 ends hanging loose near each other, at the top of the windshield. The glue and friction should hold the rope in place. While the glue is still fresh and wet, set the bottom of the windshield and gasket into place at the base of the windshield opening in the vehicle and ensure that both corners at the bottom are properly set into the inside of the cabin. Lean the windshield toward the vehicle roof and then go inside the cab. Pull the rope ends inside and if you are careful you can begin to pull the lip of the rubber gasket inside with the rope... just the right pull and angle will cause the lip to come inside the cab, holding the windshield in place as well. You may run into some tight parts near the bottom, but they are not hard to pry with your fingers as long as the weather is warm. After it's all in place, pull the rope out the rest of the way (this will be somewhat difficult from the bottom but not horrible) and you are finished. It can be done by a first-timer in under an hour with minimal effort.
What else can I help you with?
Windshield wipers will not shut off 1999 Isuzu trooper?
You have to replace a relay switch for the wipers this sholud be found under the hood in the engine compartment fuse box.
How do I replace the windshield wiper switch?
How do I replace the windshield wiper switch?
How do you replace windshield washer tank 2002 trooper?
To replace the windshield washer tank on a 2002 Isuzu Trooper, first, ensure the vehicle is turned off and the battery is disconnected for safety. Remove the screws or bolts securing the tank, typically located near the front of the vehicle. Disconnect the hoses and electrical connectors from the tank, then carefully lift it out. Install the new tank by reversing the removal process, reconnecting hoses and electrical connectors, and securing it with screws or bolts.
How do you fix a pitted windshield?
Replace windshield
How do you replace the windshield wiper blades on a 2000 Isuzu Trooper?
Go to Advanced Auto Parts, buy QUALITY blades ( teflon )and they will put them on for you.... Also, PepBoys and AutoZone will install them for you free as well...
What is the towing capacity of a 1988 Isuzu Trooper?
1805kg
Where is the fuel pump 1988 trooper?
In the fuel tank.
How can you adjust front windshield wipers that go too far both ways on a 1988 Isuzu Trooper?
There may be a way, but my guess is that someone put the wrong size wipers on it. Would a shorter wiper blade eliminate the problem?
How do you replace the front windshield?
on what?
How do you replace fuel injectors on 99 trooper?
99 isuzu trooper smell gasoline in the engine compartment
Can you replace a 1998 Isuzu Trooper computer with one from a 2002 Trooper?
Depends if you can neuter the trooper computer router hooter from a cuter commuter, Super!
How much does it cost to replace a 2001 Chevy blazer windshield approx?
Windshield
