0
I replaced one on a 2004 VUE.
Remove the passenger side front tire and access panel of wheel well. I put large solid pieces of wood , like railroad ties, under frame. If the vehicle falls it will kill you.
If you do not have a tool to hold the balancer while removing the bolt you can improvise.
Make a strap wrench. I used the nylon straps electricians use to pull wires through commercial buildings. The strap can be wound around the balance in the opposite direction that you turn the bolt. The strap will overlap itself, keep it tight. Thread the strap through an opening in the frame and tie it securely to a metal rod. Keep the tension on the strap and use a wrench to turn the balancer until the rod is up against the frame. The strap will produce enough friction with the rubber on the balance and hold it while you use a break bar to remove the bolt on the end of the balancer.
Once the bolt is off you will be able to slide the balancer off the crankshaft with little effort. Next slide new one on the crankshaft "you will see the key that guides it on". Put the bolt on finger tight.
Now reverse your strap wrench. One problem the new balancer has the grooved metal pulley and the strap will not grab the metal. Fix- Take a rubber inner tube from a bicycle tire. Cut it into a flat band to wrap around the pulley. Now you can wrap the strap over the tube. The tube grabs the metal and the strap grabs the rubber.
You will need a torque wrench which you can borrow from an Auto-zone or some other parts store. Make sure the dealer ship tells you how many pounds of foot torque are need and get the wrench set properly. Use the wrench to tighten the bolt without stripping the threads out. The wrench will click and you will know you have used enough pressure. I used my legs with my foot on the wrench to get the proper amount of pressure.
This not an easy task but you can save a little money. Please put good solid blocks under the car in enough places so that it cannot fall!!!!!!!! If it does fall it will crush you. Stands are not enough
What else can I help you with?
How do you replace harmonic balancer on 2005 Chevy Colorado 3.5?
To replace the harmonic balancer on a 2005 Chevy Colorado 3.5, first disconnect the negative battery terminal and remove any components obstructing access, such as the serpentine belt and crankshaft pulley. Use a harmonic balancer puller to carefully remove the old balancer from the crankshaft. Install the new harmonic balancer by aligning it with the keyway on the crankshaft and pressing it into place, ensuring it's properly seated. Reassemble the components in the reverse order, reconnect the battery, and check for proper operation.
How can you replace the thermostat on a 2005 Saturn Relay?
how to replace the thermostat on a 2005 saturn relay3
How do you get the front head light out to replace it?
Might be useful to precise what model you need this for... Saturn relay 2005
How do you replace the front turn signal light on a 2005 Saturn Ion?
u go ask a mechanic to do it then pay them for it
Set Saturn Vue 2005 clock?
how do i set the clock in a 2005 saturn vue
How do you remove a harmonic balancer from a 2005 Mercury Mountaineer?
You must first find a very large telephone pole or concrete building, wrap a large chain around the harmonic balancer and attach it to the building or pole, now be very careful not to start the car at this point as you might damage your vehicle. find another large vehicle preferably a large pick up with at least a class3 hitch. attach this vehicle to your vehicle with a large chain prefereably at least 20 feet long. after attaching everything and making sure all is secure, very carefully and safely accelerate the pull vehicle to 30 miles per hour, the force applied should be suffiecint to remove that stubborn harmonic balancer, if one try does not work repeat. I have never tried this technique but I have been told it works. good luck or you could go see a mechanic if in doubt!
When was Saturn Relay created?
Saturn Relay was created in 2005.
Where is the coolant temperature sensor located on a 2005 Saturn ion and how do you replace it?
under the backseat and you just pull it out and put a new one right back in
What are the release dates for Saturn Return - 2005?
Saturn Return - 2005 was released on: USA: 18 November 2005 (Deep Ellum Film Festival)
How do you replace lamps of a 2005 Saturn Ion?
To replace the lamps in a 2005 Saturn Ion, first, ensure the vehicle is turned off and the keys are removed. For headlight replacement, open the hood, disconnect the electrical connector from the back of the headlight assembly, and remove the retaining ring or clip. Replace the old bulb with a new one, being careful not to touch the glass, then reassemble everything. For taillight bulbs, open the trunk, remove the access panel, and twist the bulb socket to replace the bulb.
How do you change the battery in a 2005 Saturn Ion?
use a 10mm wrench and remove the battery from the trunk compartment, and replace it with the new battery
How do you replace 2005 Saturn Vue emergency flasher?
To replace the emergency flasher in a 2005 Saturn Vue, first, locate the flasher relay, which is typically found in the fuse box under the dashboard or under the hood. Remove the fuse box cover and identify the flasher relay by referring to the diagram on the cover or the owner's manual. Once located, gently pull the relay out of its socket and replace it with a new one, ensuring it is securely seated. Finally, test the emergency flashers to confirm they are working properly.
