0
Disconnect negative cable from auxiliary jumper terminal (I believe this is the ground wire tied to the strut tower on the driver's (left) side of the car).
Unplug the connectors from the MAP sensor and (just to its front) the intake air temp sensor.
Remove the plenum support bracket bolt located rearward of the MAP sensor
Remove the bolt holding the air inlet resonator (the thing with words "multi-point injection") to the intake plenum.
Loosen throttle body air inlet hose clamp
Release snaps holding air cleaner housing cover housing
Remove air cleaner cover and inlet hoses from the engine
Unplug throttle position sensor and idle air control motor connectors.
Pry retainer tab back on throttle cable and slide cable out of bracket. Remove cable from throttle lever.
Slide Speed control cable out of bracker, if equipped. Remove cable from throttle lever.
Remove EGR tube from intake plenum.
Remove plenum support bracket bolt located rearward of EGR tube
Remove bolts holding upper intake plenum and remove plenum
Always remove the ignition cable by grasping at the spark plug boot turning the boot 1/2 turn and pulling straight back in a steady motion
Prior to removing the spark plug spray compressed air around the spark plug hole and the area around the spark plug
Remove the spark plug using a quality spark plug socket with a rubber foam insert
Inspect spark plug condition.
To avoid cross-threading start the plug into the cylinder head by hand
Tighten the spark plugs to 20 ft-lbs (28 N-m)
Install ignition cables over spark plugs
Install new gasket and position upper intake plenum. Tighten blots to 13 ft-lbs (18 N-m)
Install bolts at plenum support brackets (Same torque as above)
Install EGR tube at plenum. Tighten EGR tube to intake manifold plenum screws to 8 ft-lbs (11 N-m)
Install throttle and speed control (if equipped) cables
Attach electrical connectors to sensors.
Install air inlet tube clamp to to 25+/- 5 inch pounds (3 +/- 1 N-m)
Connect negative terminal to auxiliary jumper terminal.
What else can I help you with?
How many spark plugs in a 2001 Chrysler sebring?
Four in a four cylinder. Six in a six cylinder.
How to replace the spark plugs on a 2001 Lexus LS430?
I want to know
How to replace spark plugs on a 2001 Honda accord ex?
Get a spark plug socket and unscrew the spark plug and replace with a new one.
How do you replace the spark plugs on 2001 gmc jimmy?
through the tire wells
How do you replace spark plugs 2001 stratus rt?
Disconnect the battery, remove the spark plug cables, and remove the old spark plugs. Put in the new spark plugs, attached the spark plug cables, and connect the battery.
How do you replace spark plugs on 2001 maxima gle?
Disconnect the battery, remove the boots and wires, and remove the old spark plugs. Put in the new spark plugs, reattach the boots and wires, and connect the battery.
Why No spark at spark plugs Ford Fiesta 1250 zetec 2001?
will be either,ignition coil,,or module,,easy to replace
How do you change spark plugs on 2001 ford expedition?
how to change spark plugs on a 2001 expedition
How do you replace the spark plugs on a 2001 Deville?
TAKE OUT THE OLD SPARKPLUGS AND PUT IN NEW ONES
How do you replace the spark plugs for 2001 Daewoo Lanos?
Remove the 4 screws holding the top cover. You can then get to the plug wires and the plugs.
How many spark plugs in a 2001 cavalier?
there are four spark plugs.
How do you change sparkplugs on a 2001 miata?
Disconnect the battery, remove the spark plug wires and boots, and remove the old spark plugs. Dispose to the old plugs, put in the new spark plugs, replace the spark plug wires and boots, and connect the battery.
