0
Go buy a Haynes Auto Repair manual for your car. Roughly you do the following You have to disconnect the battery, drain the coolant or what's left of it. Remove the fan from the pump, remove the se4rpentine drive belt, you may have to remove the fan shroud, remove anything that's in your way so you can get to the pump, remove pump. Clean the areas the pump gaskets were, spotless. take new pump. Read the instrutions on the gasket dressing tube, bottle whatever; put gasket dressing on the faces where the gaskets go, following the aforementioned instructions put the new gaskets (should have come with new water (coolant) pump; if not wipe off the dressing you just applied and go get the gaskets. Now you have gaskets, you did take the new pump with you to make sure they are the right ones right? Re-apply dressing, re-install pump, and everything else in reverse order or removal. Clean up the mess, Go wash your hands.
What else can I help you with?
Why does a 2001 Yukon over heat?
low of coolant,water pump leaking,thermosat,rariator pluged,fan clutch.
How do you change the water pump on a 2001 gmc Yukon Denali?
There are several steps to changing a water pump in a 2001 GMC Yukon Denali. You must first make sure the engine is cool, and drain the radiator of coolant. You will then need to remove the air duct and housing. You will also need to move or remove the radiator hose, radiator fan shroud, serpentine belt from the alternator, water pump pulley, and old pump gasket?æto access the water pump. You can then replace the water pump, and then replace the parts that you removed.
How much should it cost to replace water pump on 2004 Yukon?
I replaced mine on a 2001 XL 5.3 and the pump cost me $160 new. I paid $100 labor.
How do you replace 2001 water pump on Montana?
To replace the water pump on a 2001 Pontiac Montana, first disconnect the battery and drain the coolant. Remove the serpentine belt and any components blocking access to the water pump, such as the alternator or engine covers. Unbolt the water pump, clean the mounting surface, and install the new pump with a new gasket. Reassemble everything in reverse order, refill the coolant, and check for leaks.
How do you replace a water pump on 2001 Grand prix?
How do you replace a water pump on 2001 Grand prix?" How do you replace a water pump on 2001 Grand prix?"
How do you replace oil pump 2001 Yukon?
To replace the oil pump on a 2001 GMC Yukon, first, ensure the vehicle is parked on a level surface and disconnect the battery. Drain the engine oil and remove the oil pan by unbolting it from the engine block. Once the pan is off, you can access the oil pump, which is typically located at the front of the engine. Unbolt the old pump, install the new one, and then reassemble everything by reversing the disassembly steps, ensuring to replace the oil pan gasket and refill with fresh oil.
How do you replace a water pump on a 2001 4runner?
To replace the water pump on a 2001 Toyota 4Runner, first, disconnect the negative battery terminal and drain the coolant. Remove the serpentine belt, then take off the timing belt (if applicable) to access the water pump. Unbolt the old water pump, clean the mating surfaces, and install the new pump with a new gasket. Finally, reassemble everything, refill the coolant, and run the engine to check for leaks.
How much should it cost to replace Yukon water pump?
If you can do the work yourself, it will cost you around $100 to replace a Yukon water pump. If you take it to a service center, it will cost at least $200 more.
How do I replace the coolant elbow on a 2001 Gran prix coolant 90 degree?
The best way to replace the coolant elbow is to remove the water pump and insert the new elbow before inserting the bolts for the water pump. Check that there are no pieces of the old plastic elbow lodged inside. Replace both elbows (if so equipt) at the same time. If you need additional information look for the write up of how to replace a water pump on a grand prix. Hope this helps. "G"
How do you replace water pump on a 2001 Ford Focus?
how to replace water pump on 2001 ford focus
How do you replace a water pump for a 2001 Ford Ranger?
how to replace water pump on 2001 ford ranger
How do replace water pump on a 2001 Mazda Tribute?
To replace the water pump on a 2001 Mazda Tribute, first disconnect the negative battery cable and remove the serpentine belt. Drain the coolant and remove any components obstructing access to the water pump, such as the timing cover or other accessories. Unbolt the water pump from the engine block, clean the mating surfaces, and install the new pump with a new gasket. Finally, reassemble everything, refill the coolant, and check for leaks.
