0
Just above the license plate you will see the plastic lens that the bulb sits inside. On either side of the lens is a screw. Take them out and gently pry out the lens. On the back will be a clip that fits into the housing. Find the realease tab and pull out the clip with the wires attached.
Now the piece attached to the back of the lens housing, that the wire clip fit into, comes off when you give it a 1/4 turn counter clockwise. Pull it out of the back of the housing and you will see the bulb. The bulb pulls straight out.
The bulb can be purchased at any auto parts store. The wired clip does not have to come off the back to get the bulb out. I just thought it is a little easier for some.
What else can I help you with?
How do you replace the fog light in the 2005 Hyundai Santa Fe?
=
How do you replace rear window brake light bulb on 2004 Hyundai Santa f e?
How do you replace rear window brake light bulb in the 2004 Hyundai Santa Fe?Read more: How_do_you_replace_rear_window_brake_light_bulb_on_2004_Hyundai_Santa_f_e
Where is the fuse for the license plate light on a Hyundai Santa Fe?
Have you tried changing the bulbs first?
How do you change license plate bulbs on 2008 Hyundai santa fe?
To change the license plate bulbs on a 2008 Hyundai Santa Fe, first, open the rear hatch and locate the license plate light assembly. Use a flathead screwdriver to gently pry the light assembly out of its housing. Once removed, twist the old bulb counterclockwise to release it, then replace it with a new bulb by twisting it clockwise. Finally, reinsert the light assembly back into its housing and ensure it is securely in place.
Replace brake light Hyundai Santa Fe?
The brake light on a Hyundai Santa Fe is replaced by removing the retaining screws, twisting the bulb, and unscrewing it from the wiring harness. A new bulb is then installed and the assembly put back in place.
How do you replace 2008 Hyundai accent license plate light bulb?
To replace the license plate light bulb on a 2008 Hyundai Accent, first, locate the license plate light assembly at the rear of the vehicle. Use a flathead screwdriver to gently pry off the light cover. Remove the old bulb by twisting it counterclockwise and replace it with a new bulb by twisting it clockwise until secure. Finally, reattach the cover and ensure the light functions properly.
How do you replace the light bulb of the license plate light of Hyundai tiburon?
there are two spots above the license plate where the lights go on each one there should be a spot where you can push the cover in and then just pull out at an angle
Replace license plate light on 2004 Hyundai accent?
should just unbolt dude. just like any other car
How do you change the license plate light on a 2006 Hyundai Elantra?
To change the license plate light on a 2006 Hyundai Elantra, first, open the trunk and locate the license plate light assembly. Use a flathead screwdriver to gently pry off the light cover. Remove the old bulb by twisting it counterclockwise, then insert the new bulb by twisting it clockwise. Finally, replace the light cover securely and close the trunk.
How do you replace the tail light bulb on a 2002 Hyundai Santa Fe?
take the two screws out. the back of the light is connected with a rubber plug un hooked it an pull off the light,twist the bulb out of the scoket. my advise replace all thre bulbs
How do you replace rear window brake light bulb on 2004 Hyundai santa fe?
To replace the rear window brake light bulb on a 2004 Hyundai Santa Fe, first, open the rear hatch and locate the light assembly. Remove the screws or clips securing the light assembly cover, then carefully pull the assembly out. Twist the bulb socket counterclockwise to remove the old bulb, replace it with a new one, and reassemble the light assembly by reversing the steps. Finally, test the new bulb to ensure it’s functioning correctly.
Where is the oil pressure light switch located in a 2002 Hyundai Santa Fe?
The oil pressure light switch is located in the engine compartment on a 2002 Hyundai Santa Fe. It is to the right of the oil filter.
