0
To replace the tension pulley on a 1998 Oldsmobile Regency, start by disconnecting the negative battery terminal to ensure safety. Use a wrench to relieve tension on the serpentine belt by turning the tensioner pulley, then remove the belt from the tension pulley. Unscrew the mounting bolts securing the tension pulley and replace it with the new one. Finally, reinstall the serpentine belt and reconnect the battery terminal.
What else can I help you with?
What do you need to loosen to change the serpentine belt on a 4 cylinder 1998 jeep wrangler?
u need to relaese tension on the tension pulley. this is usually done with a long socket wrench handle. when u release tension and remove belt you then release tension on pulley until you have routed new belt . you then move tension pulley again until you can put belt on it, then release pulley and it will automatically provide correct tension
How do you replace the serpentine belt for a 1998 Grand Am?
For most cars and trucks there is a diagram showing the pattern the belt should take for each pulley. This is usually located under the hood on the radiator support. The vehicles I've had experience with have an idler pulley which supplies tension on the serpentine belt. This pulley is spring loaded, by using the correct size wrench, pull up on the pulley, relieving the tension on the belt and sliding the belt off or on.
What is a tension pulley looks like on a 1998 ford contour?
Its similar to the 97 pulley however some advances were made primarily in the metallurgy processes during manufacture, it still retains the tension capability however at an increased pulley factor.
How do you replace a serpentine belt for a 1998 Nissan Pathfinder?
There is either a tensioner or an adjustment screw on a pulley. A Haynes manual or Chiltons manual will help with the routing of the belt, and how to adjust the belt tension as well. Usually the idler pulley is used, before loosening the top bolt , loosen the center bolt of the pulley.
How o you replace alterntor on 1998 Pontiac bonnevile se?
first disconnect the battery - use a long breaker bar and socket to take tension off the tension pulley and at the same time remove the belt from the alternator pulley. disconnect the wires to the alternator make note of their positions. Then remove the 3 mounting bolts from the alternator.
How do you replace the belt in a 1998 Rodeo?
There is an idler pulley that holds tension on the belt. Use a 14mm socket with a long breaker bar to push the pulley down and the tension drops from the belt and it will slide off. Instalation is the same. The idler is the second pulley down from the left side of the engine while facing it. If the bolt starts to turn stop, you are either on the wrong pulley or you need to move the bar clockwise to get a lower starting point.
How do you tighten a serpentine belt for a 1998 Ford Contour?
Buy a Chevy!!!! That was a big help. Most but not all serpentine belt systems have a spring loaded tension pulley that just holds constant tension on the belt. If there is a tension pulley, it will be the one pulley that is not attached to anything like the alternator or AC. After that, the alternator is the most likely to be the one that adjusts.
When was Regency Television created?
Regency Television was created in 1998.
Is the tensioner pulley the same as the idler pulley on a 1998 Chevy cavalier?
No, the tensioner pulley and the idler pulley are not the same, although they serve similar functions in a vehicle's serpentine belt system. The tensioner pulley is designed to maintain the proper tension on the belt, while the idler pulley guides the belt and helps maintain its path. In a 1998 Chevy Cavalier, the tensioner pulley is adjustable to compensate for belt wear, whereas the idler pulley is typically fixed.
How do you change alternator belt on a 1998 Nissan maxima?
loosen the tension pulley bolt which is in the middle of the pulley, use a wrench, little work space is provided, just a little bit, then lossen the bolt that is behind the pulley, tho relive tension in the belt. take off the belt, and put on new one and tighten the bolt behind the pulley till belt is tight, then retighten the pulley bolt.
How do you replace an idler pulley on a 1998 Mercury Villager?
To replace the idler pulley on a 1998 Mercury Villager, first, disconnect the negative battery terminal to ensure safety. Next, remove the serpentine belt by loosening the tensioner pulley with a wrench, then slide the belt off the idler pulley. Unbolt the old idler pulley using a socket wrench, and install the new pulley in its place. Finally, reattach the serpentine belt and reconnect the battery terminal.
How do you put a pulley on a tensioner in a 1998 dodge caravan?
You have to unscrew the tensioner bolt and remove the serpentine belt first, then change the pulley and replace the belt.You have to unscrew the tensioner bolt and remove the serpentine belt first, then change the pulley and replace the belt.
