answersLogoWhite

0

To reset the ecu, simply disconnect the battery terms for 90 sec. People say 60 sec. but I do 90 just in case. When you say "relearn", do you mean learn the same program that's already written in the ecu, or do you mean learn a completely different set of commands? If it is the first one, an ecu immedietly starts to follow the same commands but it can take a while if something has been altered such as AFR. This will cause the car to run rich or lean.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you reset the ECU on a Mitsubishi Lancer?

To reset the ECU on a Mitsubishi Lancer, disconnect the negative battery terminal and leave it disconnected for about 10-15 minutes. This allows the ECU to clear its memory and reset. Afterward, reconnect the battery terminal, and start the vehicle to allow the ECU to relearn its parameters. It's advisable to drive the car for a short distance to help the ECU recalibrate settings.


How do you reset the computer after battery replacement in a 1998 dodge caravan sport?

You don't reset the computer. The ECU will relearn after a few driving cycles. No input necessary on your part. Just drive normally.


How can you reset an ECU on a Kia Sedona?

How can you reset an ECU on a Kia Sedona


How do you reset the computer on 2003 ford expedition after engine swap?

If you mean for fuel mix etc comp will reset and relearn after a long enough battery disconnect. As long as engine trans combo matches computer you are fine. If you did a swap, you don't reset it, you get an ECU that matches your combo


How do you reset ecu 1991 dodge stealth?

This Works Every Time. Disconnect the Battery and Stepupon the BrakePedal to Discharge any Latent Voltage.Then reconnect the Battery and Drive like Crazy to Allow ECU to Relearn Your Diving Habits. GoodLuck! It did wonders for my 1991 RT.


Where is ECU reset button for a 1991 Toyota cressida?

There is no ECU reset button.


Is there another ecm that will fit a 1990 Plymouth laser rs NT?

if your talkin about the ecu(engine control unit) any 1990 dsm (talon, eclipse or laser) non turbo ecu will fit the 1991-94will fit after mods to the 6 pin an 14 pin an coil pack wire switched


How do you reset the ecu for 97 Nissan 240sx?

you push the reset button on the back of the ECU.


Where is check engine reset button on 1991 Suzuki Sidekick?

pull dome fuse above knee. in fuse box. pulling battery makes ecu relearn everything. dome fuse resets memory only. Maybe just disconnect battery for a couple of minutes and it will reset


How do you reset dash indicators Toyota Tundra?

To reset the dash light indicators on a Toyota Tundra the trucks ECU will need to be reset. The simple way of resetting the ECU requires disconnecting the battery for 5 seconds. When the ECU is reset the lights will be clear.


How do you reset the ecu on BMW 316 compact?

Depend the number of the ecu and year of the car, general you can reset it, just recoded. The other option is, change the ecu and reset the ews and then you can redode the imobilizer with software machine. www.autocentralinas.com


How do you replace the ERG valve in a Mazda Tribute?

purchase it with a gasket and replace it but it doesn't work some time if you looking forward to kill your check-engine light. The Mazda Tribute ecu has to relearn/ reprogram itself(1)You could take your vehicle to the nearest Mazda dealer get your computer "flashed". (2) you could reset Your ecu by using a obt2 code reader.(3) you must drive your vehicle For 20 minutes for your ecu to relearn its readings from the new egr valve/sensor.............."BUKUBU!LT" B I G Island HAWAII