answersLogoWhite

0

Procedure:

1) Let engine cool down for at least 1 hour before beginning.

2) Follow the instructions in this article to drain the cooling system

3) Un-plug the coilpack wiring harness. The retaining clip is on the bottom of the plug. Press it upwards while pulling the plug toward you. (see diagram below)

4) Unbolt the EGR tube brackets with a 13mm socket and a 10mm open-end wrench (see diagram below)

5) Push the EGR tube down a little bit to give you working room to access the bolts on the thermostat housing 5a (optional) I remove the battery and the battery case to allow more room to have for a work space.

6) Using pliers, squeeze the clip on the upper hose, and slide it away from the end of the hose. Release pressure on the clip, then pull the hose straight away from the thermostat housing to remove it. (see diagram below)

7) Using the ratchet and a 10mm deep well socket, remove the 3 bolts holding the thermostat housing to the cylinder head. Use a finger ratchet if needed. (see diagram below)

8) Using pliers, squeeze the clip on the rear hose, and slide it away from the end of the hose. Remove this hose the same way you removed the hose in step 6.

9) Once the rear hose is removed, you can push the thermostat housing -- still attached to two more hoses -- down and under the hard, black A/C tube. This will help you remove the remaining two hoses on the front of the thermostat housing. Again, remove these hoses the way you did in steps 6 and 8. The housing will be completely removed at this point. You can see the damaged housing in the picture below. This is very common:

10) Using a TORX T25 driver, remove three the screws attaching the thermostat retainer.

11) Pull the thermostat out of the housing.

* During re-assembly, you will need to re-use the old thermostat and thermostat retainer. The new housing does not come with these parts.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you replace the lug nuts on a 2003 Ford Focus in the front?

how to change the lug nuts in the front of a 2003 ford focus


Where is the thermostat on a 2003 ford focus 2.3l dohc?

On the engine, in the outlet, at the base of the top hose.


Where is the thermostat located in a 2003 Ford Focus?

In the top radiator hose fitting opposite the radiator, on the engine.


Where is the thermostat in a 2003 Ford Focus zts?

It is located at the point where the upper radiator hose connects to the engine.


How do you change the thermostat in a 2000 ford focus SE wagon?

Replacing the thermostat in a 2000 Ford Focus SE wagon is very easy to do. First the radiator hose will need to be disconnected from the thermostat. After the hose is drained and disconnected, the thermostat can be removed by taking the two bolts off.


How do you change thermostat in a 1999 Ford Contour?

how do you change a thermostat for a 1997 Ford Contour


How do you change a thermostat on a 2004 ford expedition?

how to change a thermostat on a 2004 ford expedition


Do you have to change spark plus in a 2003 ford focus?

Unless you have fuel injection.


Why is my Ford Focus Overcooling?

thermostat sticking


Where is the thermostat located on 2003 Ford Focus zx3?

On the opposite end of the top radiator hose, away from the radiator, in the inlet fitting.


How many valves does the 2003 Ford Focus have?

The 2003 Ford Focus has 16 valves.


How do you replace the thermostat on a 2003 Ford Escape?

The thermostat, in your 2003 Ford Escape, by removing the water hose and the 3 bolts from the thermostat housing. The thermostat will easily come out. Reverse the process to install the new thermostat.