0
Hold the outside two buttons to clear the memory. Then hold in the button you want to program and the remote button to learn from at the same time. The blinking should change to a faster pace. No idea what makes this part happen. I must have done this step 50-100 times before it picked up my remote (maxim_83: this may depend on the learn-from-remote-control, but pressing and releasing the learn-from-remote-control as opposed to just holding it helped really well in my case; my maxima remote picked the signal up in seconds). After it picks up the signal, push the learn button on the garage opener. Then, push the visor button you programed. The garage opener light should flash and you will be done.
A good idea would be to unplug the opener while you are trying to learn the code. I didn't and the repeated attempts overheated the opener. It's also less anoying to not have the door opening and closing a million times.
Eventually, I was able to program both my garage doors. I still don't know what makes a difference. I didn't see any advantage to holding them both the 90 secs like they say it may take. Seems like the times it did finally take, it was in the first 15 seconds. I think it must be the newer frequency openers, because I had no problems with the older Craftsman openers. Thanks to the Nissan Forum for this
What else can I help you with?
How do you set up a door opener in Nissan Maxima 1998 SE?
If it is a homelink system (factory) the proceedure is in the owners manual. You will need an operational opener for your garage.
How do you program the garage door opener on a Volvo?
how do you program your garage dorr opener to your Volvo 2001 v70
How do you program the garage door opener in a 1998 Cadillac catera?
How do you un program garage door opener
Program 2002 Nissan Maxima garage opener?
To program a 2002 Nissan Maxima garage opener: Turn ignition to "ON." Hold the garage remote close to the car’s HomeLink buttons (on visor or mirror). Press and hold both the chosen HomeLink button and the remote button until the indicator light changes from slow to rapidly blinking (about 20–30 seconds). For rolling code openers: Press the "Learn" button on your garage motor, then return to the car and press the programmed HomeLink button 2–3 times. That’s it—you’re set.
Home to program garage door opener to Honda Ridgeline?
program garage door opener for honda ridgeline
How do you program a craftsman garage door opener 139.53876 to a Chamberlain garage door opener?
no
How do you program garage door opener in 2002 Chevy Venture?
how do I program a garage door opener for a 2002 chevy venture
How do you program garage door opener for 2000 Nissan maxima?
To program your on-board factory garage door opener on your Maxima's visor, you first have to press and hold the first and third (outer two) buttons down at the same time for about 15 seconds without letting them go. Then, the middle button's red light will start to flash. When this happens, let go of the two outer buttons and immediately get your original garage door opener and hold it right near your visor, aiming it right at the three buttons. Press and hold the middle button down for about 5 seconds while you simultaneously press and hold your original garage door opener's button down for this same amount of time (5 seconds). After this process is complete, wait a few seconds and you should now be able to use this middle button as your "new" garage door opener!
How do you program garage door opener for a 2006 cadillac dts?
how do i program my garage door opener to work with my 2006 dts cadillacqe
How do you program a garage door opener for a 2007 Cadillac Escalade?
quick way to program garage opener with 2007 cadillac escalade.
How do you program garage door opener in 07 gmc Yukon Denali?
how do you program my garage door opener in 2009 gmc yukon
How do you deprogram the garage door opener for Nissan Maxima 2000?
To deprogram the garage door opener for a 2000 Nissan Maxima, start by locating the HomeLink buttons in your vehicle. Press and hold the first button you wish to deprogram until the LED indicator begins to flash (usually around 20 seconds). Then, release the button and press it again for a few seconds to confirm the deprogramming. Repeat this process for any additional buttons you want to deprogram.
