0
= = How to Replace a Leaking Radiator Hose = = Replacing a leaking radiator hose can be easy and quite painless on most cars. Check that both ends of the leaking hose are easily accessed before attempting this repair, because on some cars the hoses are tightly tucked away and this job might be better left to a professional. Difficulty: Challenging Step1 Turn off the engine as soon as you suspect a leak, to prevent the engine from overheating. Step2 Determine which radiator hose is leaking and exactly where the leak is coming from by looking for wetness. Step3 Purchase 1 gallon of antifreeze and the correct replacement radiator hose from your local auto-parts store or dealer. (Radiator hoses are not interchangeable. They come in specific sizes and shapes for your particular car model.) Step4 Wait for the engine to cool down for at least 20 minutes, before beginning any work on the cooling system. Step5 Place a large pan or wide bucket on the ground under the hose to catch the coolant. Step6 Use a screwdriver to loosen the hose clamps at both ends of the hose you are replacing. Step7 Remove the radiator hose by twisting and pulling where it connects to the radiator and engine. If the hose won't budge, use a utility knife to cut it off the fittings. Step8 Remove the hose clamps from the old radiator hose and slide them onto the new hose. Step9 Put the new radiator hose on. Spray the inside of the hose ends with WD-40 if the hose is hard to get on. Tighten the hose clamps. Step10 Refill the radiator and the coolant reservoir with a 50-50 mixture of water and antifreeze. Step11 "Burp the cooling system" by running the engine with the radiator cap off until the engine warms up. Keep the engine running until both the upper and lower radiator hoses feel warm (this indicates that the thermostat is open and the coolant is flowing through the entire system). Burping the cooling system allows any air bubbles to escape. Add coolant to the radiator as needed. Step12 Look for leaks. Inspect around the hose clamps for dampness. Tighten the hose clamps if there is any wetness. Step13 Put the radiator cap back on. Step14 Check the coolant level after driving, to ensure there are no leaks. · If the leak is coming from around the clamp holding on the hose end, tighten the clamp with a screwdriver. This may be all you need to do if a loose clamp is causing the leak. · In a pinch, you can add either plain water or pure antifreeze if that's all you have, but your cooling system normally uses a mixture of 1/2 antifreeze and 1/2 water. · Never open the radiator cap or loosen a radiator hose clamp when the engine is warm or hot. The coolant could spray out and burn you. Dispose of used coolant properly. Bring it to a repair shop or parts store for recycling. Do not pour it down the sink or into the gutter..
What else can I help you with?
How do you replace ball joints on a 1999 ford expedition?
which ones? upper or lower?
1999 ford expedition radiator cap?
The radiator cap is on top of the radiator.
How do you replace lower radiator hose on 1999 Isuzu amigo?
To replace the lower radiator hose on a 1999 Isuzu Amigo, first, ensure the engine is cool and then disconnect the negative battery terminal. Drain the coolant by opening the radiator petcock, then loosen the hose clamps at both ends of the lower radiator hose and remove the old hose. Install the new hose by securing it with the clamps, refill the radiator with coolant, and check for leaks before reconnecting the battery.
How to drain radiator in 99 Ford Expedition?
To drain the radiator on a 1999 Ford Expedition, place a bucket under the radiator. Unscrew the radiator drain hose or valve on the bottom of the radiator. Remove the radiator cap.
Where is the spare tire crank on a 1999 Ford Expedition?
On a 1999 Ford Expedition : It's supposed to be at the front of the engine compartment , on top of the radiator support
Where is the radiator drain on a 1999 Ford Expedition?
follow the upper radiator hose where it goes into the top of the motor and it will be right there.
Where is the radiator cap on the Eddie Bauer Ford Expedition 1999?
On your 1999 Ford Expedition : The thread on cap on your engine coolant reservoir ( located at the front of the engine compartment , on the drivers side ) is the pressure cap / radiator cap
How do you replace a 1999 Ford Expedition horn?
with a wrench
Where is the location of the drain for the radiator on a 1999 Mercury Cougar?
SLIDE OFF THE LOWER RADIATOR HOSE AT THE RADIATOR...
How do you drain radiator 1999 Buick Century?
Open the petcock or remove the lower radiator hose from the radiator.
How do you replace a radiator in a 1999 Chevy Venture?
To replace the radiator in a 1999 Chevy Venture, start by draining the coolant from the radiator by removing the drain plug or disconnecting the lower radiator hose. Next, remove any necessary components such as the fan shroud and any hoses connected to the radiator. Unbolt the radiator from its mounts and carefully lift it out. Install the new radiator by reversing the removal steps, ensuring all connections are secure before refilling the coolant and checking for leaks.
Where is the jack handle stored on a 1999 ford expedition?
under hood in front of radiator
