answersLogoWhite

0

NO. It should start at about 150 LBS. PER cylinder. And you can't have anymore then a 15 Lb. difference in any cylinder, are the engine will idle rough.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Is 60psi a good cylinder compression for a Chevy?

NO. That is to low. If it is a good tight engine it should have at least 150 PSI per cylinder. You can not have any more of difference then 15 LBS per cylinder are the engine will idle rough.


What is the individual cylinder compression for a 350 Chevy engine?

around 80 ft.llbs. or higher is usually good.


What should the compression be on a 1985 454 Chevy truck?

A good 454 will have at least 150 PSI per cylinder.


What is the compression for a 1989 Chevy TBI 5.7 in a truck?

That engine FRESH / NEW should have 150 LBS. compression per cylinder. If you have more then 20 LBS. difference in any cylinder then it is not in good shape and a good VALVE JOB is probley in the furture.


What is the inidivual cylinder compression of a 1986 Chevy 454 truck engine?

You will have to do a compression test yourself to know that. A engine that is in good shape should have at least 150 LBS. per cylinder. There can not be more then 20 LBS. difference in any cylinders. It has to have at least 100 LBS. for the cylinder to fire at an Idle.


What could be the reasons for one cylinder not working if the spark plugs and wiring have been changed on a 1989 Chevy Celebrity 2.8 liter engine?

Run a compression test before you spend too much time checking out other potential problems. If the compression tests good, try swapping the fuel injector with a good cylinder and see if the dead cylinder moves.


Why won't your 88 chevy s10 v6 cylinder fire even though the plug and wire has been tested and is good?

Do a compression test on all the cylinders. You may find a mechanical problem with that dead cylinder.


What should the cylinder compression pressure be in a good running 1996 Chevy Silvarado 5.7 V8?

i'd like to see 130-140 psi. gotta have 90 to fire.


How do you get 400 hp from a 350 Chevy?

Good compression, good heads, good cam.


350 Chevy compression?

The compression ratio of a 350 Chevy engine usually ranges from 8.0 and 9.0 to 1. This provides a good balance of fuel economy and power.


What is the minimum fuel pressure on a 97 Chevy vortec 350?

good pump, 66 psi , key on engine off, less than 60psi, hard starting, I know , its crazy...


Is 140 psi good cylinder compression for 1992 honda?

Yes very well

Trending Questions
What fuse is used for washer pump mystique 1998? Had battery replaced on 1998 Mystique but radio and overhead lights won't turn on Not a blown fuse is there a security code you need Where would you find this in the owner's manual? How has the Model T improved What is different about the Model T compared to when it was first invented? Where are the locations of the crankshaft sensor and knock sensor on a 1998 Mercury Villager? How to do a V6 to V8 engine swap in a 1993 Chevy half ton 4X4 pickup? Can you take a mustang transmission and put it in a F-150? Where is the crankshaft position sensor on 97 s10 blazer with 4.3? Why your air conditioner blows hot air on your 2001 Chevy venture? What is the payload capacity of 2002 2500 cummins quad cab 4 x 4? When was Chevrolet Cobalt created? Does the dome light come on when you open the doors on a 2010 pt cruiser? 1990 bronco shift-no fly transfer case to manual shift? Why my 1991 4.3 s10 starts for about 3 seconds and shuts down? Will a 1998 ws6 bumper and Hood fit on a 1995 trans am? When Towing a trailer on your van should overdrive b on? How much oil can ls3 6.2 engine hold? When you are changing the rear turn signal bulb on a 1999 Chrysler Intrepid after you remove all of the plastic wing-nuts how do you remove the tail light assembly? What would cause a soft brake pedal on a 2000 Grand Caravan? How do i replace a front window regulator for a 2003 Lincoln navigator? What caused ball joint to break in half lower ball joint snaped in half?