answersLogoWhite

0

press the oil botton to bring up oil life then press and hold the reset button for 5 seconds, back to 100%.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you set a tpi sensor on an 1985 Oldsmobile regency 3.8 motor?

some tps sensor are none adj.most gms others adj. .5volts to 1volt


Where can a set of Coach Lights that were used on a 1978 Oldsmobile Regency be found?

at a local junkyard or try looking up nos(new old stock) parts for your car


How do set the time on 1992 the Oldsmobile achieva?

How to set clock on a 1992 oldsmobile achieva


Where do you charge the ac on a 1988 98 regency?

To charge the air conditioning on a 1988 Oldsmobile 98 Regency, locate the low-pressure service port, which is typically found on the larger diameter aluminum line between the compressor and the evaporator. Make sure the engine is running and the A/C is set to the maximum cold setting before connecting the refrigerant can. Always use the correct type of refrigerant specified for the vehicle, and check for leaks before charging. If unsure, it's advisable to consult a professional mechanic.


Spanner symbol on citroen saxo dashboard what does it mean?

It is there to remind you that a general service is needed. It is not telling you about any particular problem with the car.this is a service indicator, you set it for the desired timing and it counts down the miles to you nxt service.


What is Stabliltrak how do you service it indicator light says it needs servicing?

You will need a scanner that can display the fault codes set in the module. The codes will help you determine the problem.


Reset oil indicator 2000 BMW 323i?

The reset oil indicator on a 2000 BMW 323i warns the driver that it is time to service the engine. It is automatically set to trigger every 3,000 miles and can be reset once the oil has been changed.


On a 91' Oldsmobile regency elite how do i control and set the buttons especially the destination button to make the eta effective ie destination trip odometer Litres used ENTEROFF all dash buttons?

To control and set the buttons on a 1991 Oldsmobile Regency Elite, start by pressing the "DEST" button to access the destination settings. Use the arrow keys to navigate and input your desired destination, then press "ENTER" to confirm. For trip odometer and fuel usage, toggle through the display options using the "TRIP" button, while the "OFF" button can be used to reset any displayed values. Ensure that the dashboard buttons are functioning properly for seamless operation of these features.


How many pieces come in a box of Denby Regency Green dinnerware?

The Denby Regency Green Dinnerware set comes equipped with 16 difference pieces. The set includes four pieces each of mugs, bowls, salad plates, and dinner plates.


How do you set the clock in a 99 Oldsmobile alero?

How do you set the clock in a 1999 Oldsmobile Alero? I did not receive a book with the car and I really would like to have the right time in my car.


Why can't I reset service 4wd I have a 05 Chevy Silrado with 63000 my service 4 wd indicator came on at 50000I reset it now at 63000 it's on again and won't let me reset. shift indicator lights inop?

My 2005 Chevy 4wd, ext. cab,shrt bed, has push buttons to go from(from top to bottom) Auto 4wheel drive, to 2 High , then to N(neutral), and then to 4 high, then to 4 low. At approx. 50,000 mi. the service indicator light came on and indicated "Service 4wd." I re-set the indicator, and forgot about it. Now, at 63,000 mi. it's telling me to service the 4wd, only this time the reset works until I turn the ignition off. when I restart, the service light comes on. However, the indicator lights that show which gear the transfer case is in, does not light up, and there is no automatic shifting of the transfer case. Is there a simple solution to this problem? Recommendations...Please! popo63


How do you set the clock in a 1992 Delta 88 Oldsmobile?

To set the clock all factory installed audio sysyems: 1. With the radio off and the ignition on, press SET. The SET indicator will appear on the digital screen for five seconds. 2. During those five seconds, you can set the clock to the correct hour and minute by pressing the SCAN and SEEK buttons. SCAN sets the hour. SEEK (up or down) sets the minute.