0
What else can I help you with?
What is the torquing specs for the bolts on a 1999 blazer 43 intake manifold The book gives 132 pounds but this seems too much?
I FOUND THIS AT WWW.AUTOZONE.COM, CLICK ON VEHICLE SPECS . For your 1999 CHEVROLET TRUCK BLAZER 2WD: INTAKE BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE LOWER MANIFOLD BOLTS TO 27 IN/LBS TORQUE LOWER BOLTS TO 9 FT/LBS TORQUE LOWER BOLTS TO 11 FT/LBS TORQUE UPPER MANIFOLD BOLTS TO 44 IN/LBS TORQUE UPPER MANIFOLD BOLTS TO 7 FT/LBS (TO TORQUE BOLTS & NUTS, START IN CENTER USING CRISSCROSS PATTERN)
What are the exhaust intake manifold torque specs for a ford 19l engine?
According to the Chilton manual, the torque settings are 15 to 20 foot pounds or 21 to 27 Newton Meters.
What is the oil drain plug torque specs 2001 town and country?
For a 2001 Chrysler Town and Country, the oil drain plug torque specification is typically around 20 to 25 foot-pounds (27 to 34 Nm). It's important to ensure the drain plug is properly tightened to avoid leaks, but be cautious not to overtighten, as this can damage the oil pan. Always refer to the vehicle's service manual for the most accurate specifications.
Head bolt torque specs c-10 caterpillar engine?
99-121 foot pounds plus 90 degrees, small bolts 27-33 foot pounds
What are the torque specs for 1999 Yamaha big bear 350?
For the 1999 Yamaha Big Bear 350, the torque specifications vary by component. Generally, the engine case bolts are typically torqued to around 7.2 ft-lb (10 Nm), while the cylinder head bolts should be torqued to 15-20 ft-lb (20-27 Nm) in a specific sequence. Always refer to a service manual for the exact specifications and procedures to ensure proper assembly.
What are the release dates for Crashbox - 1999 1999-02-27?
Crashbox - 1999 1999-02-27 was released on: USA: 27 February 1999
What are the release dates for Crashbox - 1999 1999-03-27?
Crashbox - 1999 1999-03-27 was released on: USA: 27 March 1999
What are the release dates for Under the Helmet - 1999 - 1999-11-27?
Under the Helmet - 1999 - 1999-11-27 was released on: USA: 27 November 1999
What is the torque for the oil drain plug for a Chrysler Sebring?
The torque specification for the oil drain plug on a Chrysler Sebring typically ranges from 15 to 20 foot-pounds (20 to 27 Newton-meters). It's important to refer to the specific model year and engine type, as specifications can vary slightly. Always ensure the drain plug is properly cleaned and use a new washer if required for a good seal.
What is the torque specs on the front wheel on a Kawasaki vulcan 1500?
The torque specification for the front wheel axle nut on a Kawasaki Vulcan 1500 is typically around 72 ft-lb (98 Nm). For the brake caliper mounting bolts, the torque is usually in the range of 20-25 ft-lb (27-34 Nm). Always refer to the specific model's service manual for the most accurate and detailed specifications.
What day of the week was October 27 1999 on?
October 27 1999 was a Wednesday.
What is the torque spec for a 1999 stratus brake caliper banjo bolt?
The torque specification for the brake caliper banjo bolt on a 1999 Dodge Stratus is typically around 20-25 ft-lbs (27-34 Nm). It's essential to use a calibrated torque wrench to ensure proper tightening, as over-tightening can damage the brake components. Always refer to the vehicle's service manual for the most accurate and specific information.
