0
What else can I help you with?
How many inches does 10mm equal too?
0.3937007874 in Direct Conversion Formula 10 mm* 1 in 25.4 mm = 0.3937007874 in
How do adjust the handbrake on your vauxhal vectra?
lift the handbrake boot thing up from around your hand brake lever there is a 10mm nut tighten it up not too much other wise ur back wheels wont turn or will lock up you may need a 10mm long socket not a short-normal 1
Where is the Intake Air Temperature sensor on 2000 Kia Rio?
open the bonnet look too your right in between the engine and gearbox u will find a wire leading to the crank sensor held by a 10mm bolt. will require a 10mm socket 3/8 swiffel joint and ratchet. please recommend me if u find it im only helping
How can you get a valve cover stud out of a 1991 Honda Civic LX as it broke off by tightening the nut too hard The gasket needed replacement due to a bad oil leak?
To get the valve cover stud out all you need is a 10mm socket and rachet it and after the valve covers off it should just come right off using the socket. but you will have to replace it
What is the standard height of piano keys and how does it affect the player's performance and comfort?
The standard height of piano keys is about 10mm. This height is important for the player's performance and comfort because it allows for proper finger control and technique. If the keys are too high or too low, it can affect the player's ability to play accurately and comfortably, leading to potential strain or injury.
Are sparkplugs in a 1998 Outback too difficult for the average person to change?
Spark plugs in a 98 OutbackThe left hand side isn't too bad although it it cramped. You will need a variety of socket extensions to make sure you get the socket connection out far enough so the socket wrench to turn but not out to far or you will be coming in direct contact with the inner fender. The right hand side is trickier. Remove the windshield fluid container (2 10mm bolts) and it is at least accessible.Bottom line can a non-mechanic do it? its not easy. yes but have patience! Joe
Where is the fuel filter located and how do you replace it on a 2000 Kia Sephia?
fuel filter is located on the passenger side of car not too far from the tire, its mounted on the frame of the ca, and u need a 10mm socket to remove it from the bracket. disconnect old one from fuel line then replace new one , not that difficult to do actually.
How do you remove the ac refill port cover Volvo s60?
it unscrews with a socket sometimes by hand but if too hard use socket
Where is the fuel filter on a 2002 Ford Focus?
Pass side toward the back its up there a bit you have to look for it PS look for fuel lines, kind of hard to get too but its about a ten minute job to change..It's at the right front corner of the fuel tank, up in a recess. You need a 1/4" drive set; ratchet, 4" extension, a 6mm and a 10mm socket, and 6mm and 10mm combination wrenches. Have fun, but it really is an easy job... once you've done it.
What is 28-32 equal too?
28-32 equal too = -4
How do you loosen the distrbutor hold down bolt on 1993 roadmaster What tool is best if bolt is too tight?
To loosen the distributor hold-down bolt on a 1993 Roadmaster, use a socket wrench with the appropriate size socket, usually 5/16" or 10mm, depending on the specific engine. If the bolt is too tight, a breaker bar can provide additional leverage. Alternatively, applying penetrating oil and letting it sit for a few minutes can help loosen the bolt before attempting again. Always ensure to work carefully to avoid damaging the distributor or surrounding components.
1998 Subaru Outback has no power to lighter?
Short of a vague wiring problem there are two(2) high probability causes: 1) the obvious, appropriate fuse, and 2) a cigarette lighter socket fusible safety device. The latter is on the rear of the socket (or built into it), designed to fail and break the current flow (i.e. heating) if the socket gets too hot, as may occur when the plug is held in, or sticks. It also may fail from extensive use, over time. The appropriate fix for the socket failure is to replace the socket, utilizing standard electrical safety practices, and making sure the new socket and "plug" are compatible.
