answersLogoWhite

0

Three

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How current passes through resistor.?

What is the current running through resistor four?1 amps..!What is the current running through resistor one? 3 amps...!What is the current running through resistor three? 2amps..!What is the current running through resistor five? 3 amps..!What is the voltage drop running through resistor five? 45 volts...!What is the equivalent resistance through the parallel portion of the circuit? 6 ohmsAnswerA resistor is a conductor, albeit one with a higher resistance than a length of wire, so current passes through it without any problem. The magnitude of the current will, of course, be somewhat lower because of the additional resistance.


What is the voltage drop running through resistor one?

What is the voltage drop running through resistor one


Consider two identical resistors wired in series one behind the other If there is an electric current through the combination the current in the second resistor is?

Two resistors wired in series (no mater if they have the same resistor value or not) will always have the same amount of current flowing through them. Therefore, the current flowing through the second resistor will be equal to the current flowing through the first one. The current through every component in a series circuit is the same. The voltage across every component in a parallel circuit is the same.


A 120 ohm resisto a 60 ohm resistor and a 40 ohm resistor are connected in parallel to a 120 volt power source What is the current running through the 60 ohm resistor?

If they're in parallel, then each resistor acts as if it were the only one,and the presence of any others is irrelevant.The current through the 60-ohm resistor is I = E/R = (120/60) = 2 amperes.


What is the voltage drop that is running through resistor one?

nine or 9


A 120 ohm resistor a 60 ohm resistor and a 40 ohm resistor are connected in parallel to a 120 volt power source What is the current running through the 120 ohm resister?

If they're in parallel, then the resistors have no effect on each other. The current through each one is the same as it would be if the others were not there at all. The current through the 120Ω resistor is 120 volts/120Ω = 1 Ampere. The 60Ω and the 40Ω are red herring resistors.


Does current flow through a resistor or across a resistor?

Normally through the resistor's internal construction. It flows through any part of the resistor that has low resistance- be it anywere. And then there's this. It might be that one should consider that current flows through a resistor and voltage is dropped across a resistor. Perhaps this is where the question began. The former is fairly straight forward. The latter can be vexing. Voltage is said to be dropped across a resistor when current is flowing through it. The voltage drop may be also considered as the voltage measureable across that resistor or the voltage "felt" by that resistor. It's as if that resistor was in a circuit by itself and hooked up to a battery of that equivalent voltage.


Is an resistor an conductor or a insulator?

A resistor is a conductor that dissipates some of the electrical energy fromthe current flowing through it. The energy dissipated by the resistor is(current through it)2 x (resistance)


Which one of the following equations could be used to calculate the power absorbed by a resistor?

p=I*I*R ,P=V*V/R;where I is the current passing through the resistor, and V is the voltage across resistor, and R is the Resistance of the resistor,


What is damaged resistor?

A damaged resistor is one that it fried by current that is too high


When a resistor has another one connected in parallel with it is the combined resistor greaterthe same or smaller?

Think it through. You are adding a second path for current flow. Current flow will increase to some extent. Therefore, with more current flow, resistance must....


Do you need to apply a load to see a voltage drop across a resistor?

You'll see a voltage drop across a resistor if current is flowing through it. It only has to be a part of a complete circuit, i.e. one in which current is flowing.