h11 i believe.
On the driver side, you remove the plug and rotate the bulb clockwise. On the passenger side, you access it through the cover in front of the tire. You rotate the bulb clockwise to get it out. Good luck.
change bulb on ford kuga
According to the 2005 Ford Expedition Owner Guide : Low beam headlamp ( # 9006 bulb ) High beam headlamp ( # 9005 bulb )
Removal WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may effect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp. # NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position. Disconnect the headlamp connector. # Remove the headlamp bulb. ## Rotate the headlamp bulb retainer counterclockwise one-eighth turn and remove. ## Remove the headlamp bulb.Installation CAUTION: Bulbs 9004 and 9007 look similar, but are not interchangeable. # Install the headlamp bulb. ## Install the headlamp bulb. ## Rotate the headlamp bulb retainer clockwise one-eighth turn.# Connect the headlamp connector.
with your hands ?
Removal WARNING: The halogen bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may effect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp. # NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position. Disconnect the headlamp connector. # Remove the headlamp bulb. ## Rotate the headlamp bulb retainer counterclockwise one-eighth turn and remove. ## Remove the headlamp bulb.Installation CAUTION: Bulbs 9004 and 9007 look similar, but are not interchangeable. # Install the headlamp bulb. ## Install the headlamp bulb. ## Rotate the headlamp bulb retainer clockwise one-eighth turn.# Connect the headlamp connector.
h7
take it to a trained mechanic?
HI, see "You Tube" where there is a short video showing how to change a Puma headlight bulb
you don't. take it to dealer and they will change it for free.
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
Remove the two torque type mounting screws from the headlamp and gently move the headlamp out of the way, Power cable to headlamp can be removed but not needed. Easy access to fog lamp bulb is then achieved. Disconnect fog lamp power cable and twist bulb to remove.