0
There are 15 different values: Value: Ohms 02 - 0.523 03 - 0.681 04 - 0.887 05 - 1.130 06 - 1.470 07 - 1.870 08 - 2.370 09 - 3.010 10 - 3.740 11 - 4.750 12 - 6.040 13 - 7.500 14 - 9.530 15 - 11.801 It could be any of those. If you're trying to bypass it doesn't have to be exact but it does need to be close. To make the correct value of resistor, get resistors of different values and add them up. Solder them in-line to each other. If you don't know the correct value start at the bottom and work your way up. There's a 4 minute wait between trys and the ignition needs to go to the OFF position before you start the wait.
What else can I help you with?
Can you bypass the security system on a 2000 Chevy lumina?
Yes. A resistor and a few connectors. Maybe $2
How do I remove the vats or passkey I or II on a 98 Chevy lumina?
It's a VATS system. If you know the value of the resistor you can cut the wires going to the lock cylinder and solder in a resistor of the correct value.
1990 Chevy Lumina security light on and will not start?
probably your security system . Search google for "Bypass GM Vats Security"
How do you bypass the pass-key ii security system on a 1996 Chevy lumina?
Short answer is you don't. Get the unit towed to a GM dealer for repair if required. The pass key system is integrated into the engine management computer and is nearly impossible to bypass successfully.
How can I effectively bypass a water softener system in my home?
To effectively bypass a water softener system in your home, you can locate the bypass valve on the system and turn it to the "bypass" position. This will allow water to flow through the plumbing without going through the water softener. Make sure to follow the manufacturer's instructions and consult a professional if needed.
How can you disable the hole vats system on a 1990 cadillac?
To disable the VATS (Vehicle Anti-Theft System) on a 1990 Cadillac, you can bypass the system by accessing the ignition switch's wiring. Locate the VATS module and identify the resistor that corresponds to your key's resistance value. You can then connect a resistor with the same value directly to the ignition circuit or use a bypass module. However, be cautious as this may affect your vehicle’s security system and could lead to issues with insurance or theft protection.
What does fuel pump resistor do?
A fuel pump resistor runs the fuel pump at a lower speed when the demand for fuel is lower. When more fuel is needed the system bypasses the resistor and allows the fuel pump to run at full speed.
How do you bypass a 1998 Chevy lumina's VATS security system in detail?
bypass the vats on a lumina if you have the key there should be a pellet in it. using a multi meter check the resistance of the pellet. go to radio shack and buy the appropriate resistor (s). wire the resistors into the small wires at the base of the steering column. should be a purple with white and a white with black. the car should start if not recheck everything good luck How to fix security light on the dash board? You can remove the security light Bulb from back panel of instrument panel cluster. It is ok for starting without the light bulb. But I do not know if it cause other problem?
How do you bypass passlock on 1997 Chevy lumina?
Bypassing the Passlock system on a 1997 Chevy Lumina typically involves locating the Passlock wires and connecting them directly to bypass the ignition lock. This usually requires cutting the yellow wire from the Passlock module and connecting it to the ignition wire to allow the vehicle to start without the security system engaging. However, bypassing the security system can lead to potential issues and may not be legal in some areas, so it’s advisable to consult a professional or consider repairs instead.
How do you bypass passlock system in Oldsmobile intrigue?
how do you bypass passlock system
Can I bypass the AC pulley with a shorter belt on a 98 Chevy lumina?
Yes, you can bypass the AC pulley on a 1998 Chevy Lumina by using a shorter serpentine belt. This modification allows the engine to run without the AC compressor, but be sure to check the belt routing diagram to ensure proper installation. Keep in mind that this will disable your air conditioning system, so consider your climate needs before proceeding.
How can one bypass a water softener system?
To bypass a water softener system, you can locate the bypass valve on the system and turn it to the "bypass" position. This allows water to flow through the system without being softened.
