0

Subjects>Auto>American Cars

What should a 300 6 cylinder idle at?

Anonymous

∙ 13y ago

Updated: 12/14/2022

Idle should be between 500 to 750 RPM.

Wiki User

∙ 13y ago

What else can I help you with?

Related Questions

How do you improve gas mileage on a 300 6-cylinder?

Keep the tires inflated to proper specs. Idle less, drive slower.

What is the oil pressure for 6 cylinder Jeep Cherokee Laredo 1992?

Should be at least 10 at idle. 25 at idle would be better.

How do you adjust the idle on an 1984 F-150 6 Cylinder?

On the driver's side of the F 150 carb, there should be the linkage for the throttle. On the linkage there should be a set screw that you can turn to adjust the engine idle.

Where is number one cyl on a 300 6-cylinder?

# 1 cylinder is at the front by the radiator on the Ford 300 cubic inch straight 6 cylinder

How do you adjust the idle on 2003 Grand Caravan 6-cylinder 3.3 L engine?

Idle is computer controlled and is not adjustable.

Is the 1979 300 6 chain or belt timing?

Chain if you are asking about a 300 Cu In 6 cylinder Ford.

Where is number one cylinder for a ford 300 6-cylinder?

For your Ford 4.9 liter / 300 cubic inch inline six cylinder engine : ( the # 1 cylinder is at the FRONT of the vehicle )

What is the timing for a 1974 ford F100 straight 6?

The 240 cubic inch straight 6 cylinder is ( 6 degrees BTDC ) The 300 cubic inch straight 6 cylinder is ( 10 degrees BTDC ) The 300 cubic inch straight 6 cylinder with manual transmission in California is ( 6 degrees BTDC )

Where is the 1 cylinder located on a 1986 Ford F150 straight 6?

# 1 cylinder on your 300 cubic inch ( 4.9 L ) straight 6 is the FRONT CYLINDER

How can you get the low 500 rpm idle up a little on a 1994 Jeep Grand Cherokee 6 cylinder?

The idle speed is computer controlled. If the idle is too low, there is a problem with a ssensor or the idle speed motor.

How much fuel pressure do i need to run my 1986 Chevy cavalier?

For the 2.0 4 cylinder it should be 9-13 psi, with a minimum of 13 psi deadhead pressure. With the 2.8 liter 6 cylinder it should be 5.5 to 6.5 psi at idle, there is no deadhead specification. Deadhead pressure is pressure at idle with the return line pinched off.

Dwell setting 65 mustang 6-cylinder?

35 to 38 dwell at idle RPM for your 200 cubic inch straight 6 cylinder in a 1965 Ford Mustang

Trending Questions

Where is the flasher located in a 1989 Mazda 323? How do you change the oil filter on a 2006 Passat? How do you remove an EL falcon head unit? What was the mpg on a 1996 doge ram 5.9 360 get? 97 ford f150 4.2 engine misfires on cyl 4 replaced injector and coil pack plugs and wires and also new fuel pump.why does it still run rough? What were Charles Goodyear's nicknames? Are there two signal flashers on a 2000 Cadillac eldorado etc? If you have gl1100 standard where is neutral safety switch located if the spot on the right side is blank off? Is there a picture of crank sensor location for a 1987 2.8 Chevy Celebrity? What is the firing order for a 1994 Saturn SC1 1.9L? What is a P0068 code for a 2005 Dodge Ram 1500? What type of transmission does a 1995 K1500 silverado need? How do you you remove the console 1994 Corvette? Will the Trans Am come back? 1999 town car engine starts and runs rough and soon stop when put into drive what cause this to happen? If a stock 1999 Pontiac grand prix gtp comes with 240 horse how much more hores would it have if it had a smaller pulley and msd ignition wires and plugs and a cold air intake installed? What is the rear hip room of the 2009 Cadillac SRX? When a 2001 VW Passat exceeds 10mph the doors auto lock how can you turn this annoyance off? How Low Can What if your Car Be Before Its Illegal? Where can you find an owners manual for a 1993 Jeep Wrangler?

Resources

Top Categories

Product

Company

Copyright ©2025 Answers.com. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Answers.