0
Generally for any car you will need your jack and tire iron, you will probably also need a 10mm open end wrench or socket, I can't remember the name of the other tool commonly needed, a star bit is what I have known them as, it may be needed, a large one. You may want to use a flat head screwdriver to pop off the old pads, and will need a c-clamp. The c-clamp is used with one of the old pads to push the brake cylinder(s) back to the down position. That should be all the tools you need, I have never worked on a Bonneville but this seems to be the make-up of Pontiacs. I hope I have been of some help
Just did front brakes on a 94 Bonneville. You NEED a 3/8 Allen/socket...They are hard to find but a regular Allen wrench is NOT long enough. These fit on a 3/8 socket wrench and it is HARD to brake them. Drivers side goes up. I just replaced the caliper on this car. This will be the only time you use this socket for sure.
What else can I help you with?
Your brake light wont shut off in your 1997 Pontiac Bonneville?
is your e-brake on?
How do you change front brakes on a 2002 Pontiac Bonneville?
One lifts the car on a car jack, removes the tires, remove the brake shoe, remove and replace the brake pad. Then one has to replace the brake shoe in the correct position, then put the tired back on the car.
How do you change the rear brake pads on a Pontiac Bonneville?
THERE ARE A LOT OF DIFFERENT REAR BREAKS FOR BOONEVILLES AS WELL AS ALL OTHER CARS CALL ME FOR ADVICE OR USE A LOCAL MECHANIC THANKS BOON
How do you replace the brake booster on a 1998 Pontiac transport?
how do you change a brake booster valve to a 1998 Pontiac transport
What tools are needed to change passenger front brake hose from caliper to frame on 1997 Bonneville sse?
5/16 wrench for the calliper and a 9/16 wrench for frame side.
Where is the fuse box on a 1986 Pontiac Bonneville?
The fuse box for the 1986 Bonneville is under the dashboard. The box has a small cover over it and you'll see it if you look just above the brake pedal and a little to the left.
Why does 1997 Pontiac Bonneville brake warning light stays on?
I had this problem on a 94 Bonneville after we had fixed the brakes. After I disconnected the battery and reconnected the light went off and the dinging stopped. Not sure if this was related or just coincidence.
How much does it cost to repair the brake lines on a Pontiac Bonneville?
The cost to repair the brake lines on a Pontiac Bonneville typically ranges from $150 to $300, depending on the extent of the damage and labor rates in your area. If the repair involves replacing multiple lines or additional components, the cost could be higher. It's advisable to get a detailed estimate from a qualified mechanic for a more accurate figure.
How do you replace rear brake light on 2002 Pontiac Bonneville?
To replace the rear brake light on a 2002 Pontiac Bonneville, first, open the trunk and locate the tail light assembly. Remove the screws or clips securing the assembly and gently pull it out. Disconnect the electrical connector, then twist the bulb socket counterclockwise to remove it. Replace the old bulb with a new one, reassemble the components, and test the brake light to ensure it works properly.
How many brake lines on 99 Pontiac bonneville?
under the radiator on the drivers side you have to remove the splash pan to see it not fun to get to and it drains all over things
How to change the brake pads on a 1997 Pontiac grand am?
Buy the Haynes or Chiltons book!
How do you change rear brakes on a 2006 Pontiac Montana?
Remove the 2006 Pontiac Montana wheel and tire. Remove the brake pad Springs. The brake pads will come off. Reverse the process to install the new brake pads.
