0
When changing the heater core on a 1992 ford aerostar how do you change and reconnect the hoses?
You need a Ford heater hose disconnect tool. You need the one with a handle to get back into the tight area. You slip the U shape end of the tool into the matching grove of the heater hose and push and pull back and forth and it'll come loose. I'ld replace the O rings will I had it apart. When you put it back together, you just have to push it back on. Make sure it locks into place. Or you can do it without the tool..The best way, if you're sure the heater core is gone and you are replacing it, is to cut the tubes just on the outside of the firewall or just inside whichever gives you best access. The hoses are connected to the heater with special clips which makes connection easy but disconnection almost impossible. When removing hoses make sure to mark the hoses (which goes on top) for proper replacement. be sure to use new plastic inserts available at the dealer. Use a little Vaseline or liquid soap to lubricate the rubber rings so as not to damage them and allow them to slip on easily. Cutting the heater tubes will save you a bundle in not buying the special tool.
What else can I help you with?
1997 aerostar van front heater blower guide?
1997 van aerostar front heater blower guide
How do you change a heater core in a 1998 jimmy?
Before CHanging the Heater Core, have you tried flushing it? I have a 99' Jimmy and have to do this every year to get my heater to work.
How do you change the heater core in an 89 Ford Aerostar van?
bIG JOB Get a manual on your car from DISCOUNTAUTOREPAIRMANUALS.COM and see if you want to go to that much trouble.
Where is the heater control valve on a 1991 Ford Aerostar?
Look near or behind the alternator. The valve that controls flow of coolant to the heater core on my 1987 Aerostar is located on the left wall of the engine compartment. I imagine the 1991 is similar. Trace the heater hoses from the engine/water pump and you will find it.
How do I change the gas valve on a water heater?
To change the gas valve on a water heater, first turn off the gas supply and water heater. Disconnect the gas line and pilot tube from the old valve. Remove the old valve and install the new one in its place. Reconnect the gas line and pilot tube, then turn the gas supply and water heater back on.
How do you repair a heater core on a 1994 Aerostar 30L V6 van?
The heater core will have to be replace, it is not hard to do and the Heater Core is about $35 at the auto parts store. Good Luck
How do you change the heater core in a Toyota supra 1986?
To change the heater core in a 1986 Toyota Supra, first disconnect the battery and drain the coolant. Remove the dashboard and climate control assembly to access the heater core housing. Disconnect the heater core hoses from the firewall, then unbolt and remove the heater core itself. Install the new heater core, reassemble the housing, dashboard, and reconnect the hoses, ensuring to refill the coolant before testing the system.
How can I change the gas valve on a water heater?
To change the gas valve on a water heater, first turn off the gas supply and water supply to the heater. Disconnect the gas line and remove the old gas valve. Install the new gas valve and reconnect the gas line. Finally, turn the gas and water supplies back on and test the water heater to ensure it is working properly.
Why is mist blowing on your 91 aerostar windshield?
Misting of a windshield usually indicates a leak in the heater core.
How to install a heater core on a 1992 Ford Aerostar van?
See previous question of same nature.
On a 1991 Ford Aerostar with Dual Heat why would you have water running on the ground on the passenger side?
This is an indication that your heater core is leaking. To stop the leaking you will have to replace the heater core or stop using your heater.
The heater vents in your wifes 94 Corsica change at randomit will be windshield one second then the next it will change to feet and it keeps changing randomly?
you need a new car
