0
What else can I help you with?
Do you have to drop the transmission out of 1996 Chevy s 10 to fix the hydrolic clutch resevior?
The hydraulic clutch reservoir is attached to the firewall. The hydraulic clutch slave cylinder is in front of the transmission. The transmission would have to be dropped to gain access to the slave cylinder.
Where is the slave cylinder for the clutch on a 1996 Toyota Tacoma 4x4?
The slave cylinder is located on the driver side of your bell housing going to your motor. Its a cylinder about the size of a roll of quarters.. maybe a little bigger.
Where is The Slave Cylinder on a 1996 Geo Tracker 1.6L 5 speed 16 Valve for the Clutch?
Hi, The slave cylinder is on the side of the transmission. The hydraulic clutch system bleeder valve is on the slave cylinder. If you're bleeding the cluth, remember to have a jar and some clear plastic to bleed the system and never re-use the fluid you remove from the clutch master cylinder or the slave cylinder. Good luck and I hope it's a warm day for you. Please remember to use jack stands or heavy metal ramps. Steve H.
How do you replace the slave cylinder in a 1996 Mitsubishi Eclipse RS 20?
Probably remove the transmissionm if its a internal slave, if external then its mounted on the outside of the tranny. The master clutch cylinder is located on the firewall. Bleed the system and pump the hell out of the clutch after installing the new slave. : On a 99 GST it is an external cylinder (2) 10mm bolts remove the line replace cylinder bleed system.
How do you replace the clutch slave cylinder on a 1996 V6 camaro?
to replace the clutch slave cylinder... 1. remove the two bolts that hold the slave cylinder to the bellhousing. 2. hang it from a piece of wire..NOT by the braided hose. 3. remove the little pin that holds the cylinder to the hose. ***fluid will leak out of the braided hose... 4. When the fluid has stopped, install in the reverse order...
How do you know if your hydraulic clutch on your 1996 Sunfire is going out.?
If you clutch and it either goes all the way in with no pressure there is a leak in your slave cylinder or the higher you have to clutch means your clutch is sliping and has to be replaced. If your doing a lot of power shifting i would suggest you get a racing clutch instead.
Where is the clutch slave cylinder located on Chevy 1996 Z24 cavalier?
It should be very close to the clutch bellhousing itself. Follow the hydraulic line from the clutch master cylinder down. I hope this helps you. it's actually inside the tranny between the motor and tranny good luck .....chevy boy
How do you know if the clutch cable has gone in a Ford Escort 1996?
They don't have clutch cables. It is a hydraulic clutch with a master cylinder and a slave cylinder. If the clutch won't work fill the brake master cylinder with fluid. The clutch uses the same fluid as the brake and they share the same resrvoir of fluid. Follow the line from the clutch master cylinder across the transmission to the slave cylinder of the clutch. The slave cylinder is on the front middle of the transmission/engine. Take the cover off the bleeder valve and place a clear plastic hose over the nipple into a container of brake fluid. Have someone pump the clutch several times and then hold it to the floor. This is the time for you to open the bleeder valve. Air will escape into the container of fluid. Once the bubbles have stopped close the bleeder valve and have your assistant pump the clutch again. Keep doing this procedure until there are no more bubbles. Fill the master cylinder with brake fluid while you are doing this. If it goes down to far it will get air into your brakes and your clutch.
Why does your clutch pedal stick down on a 1996 F150?
Bad or improperly installed throw out bearing? broken throw out bearing fork? hydraulic? bad slave cylinder?
What is wrong if there is no resistance in the clutch pedal for 1996 Mitsubishi Galant with manual transmission?
it means you have no clutch fluid(brake fluid) or that you possibly have a leak in the line somewhere or that it needs to be bled.might possibly be the master or slave cylinder.first check the clutch fluid resivor.if its empty then you need to top it off and bleed the line @ the master cylinder then at the slave cylinder.then find out why you have no fluid...the clutch fluid resivor is the smaller one of the two,check inside the car for a leak too,follow the clutch pedal to the firewall and you will see the small rod that goes into your clutch master cylinder,if you have a leak there the master cylinder is bad
Where is the hydraulic shift slave cylinder for 1998 Chevy s-10?
inside the transmission. http://www.2carpros.com/forum/1996-chevy-s-10-clutch-vt132269.html
How do you replace the clutch slave cylinder on a 1996 C2500 Chevy Cheyenne 350 motor w 5 speed manual tran do you have to remove the trans?
Yes you do. It is inside of the bell housing.
