0
What else can I help you with?
How can you fix your accelerator pedal in a 1990 wrangler from sticking?
you will need to replace the throttle cable, and while you are at it check the return spring.
Mechanic rebuilt carb on 1986 ford f700 370 4v four barrell carb now it will not go over 20 mph Does this sound like a float problem?
no. you have govoner? probly is missing the spring which opens the throttle the return sping is the one spring you can see. the wide open throttle spring is in the 3 bolt cover on the side of carburetor no. you have govoner? probly is missing the spring which opens the throttle the return sping is the one spring you can see. the wide open throttle spring is in the 3 bolt cover on the side of carburetor
What is a push-pull throttle cable for motorcycles?
A push-pull throttle is a very misunderstood thing. It is a dual cable throttle operation where in the pull cable is what opens the throttle plates. And, the push cable along with a throttle return spring is what closes the throttle plates.
What holds the throttle shaft in the idle position on a Briggs engine?
On a Briggs & Stratton engine, the throttle shaft is held in the idle position primarily by a combination of a throttle return spring and the governor system. The throttle return spring provides tension to keep the throttle in the idle position when no other forces are acting on it. Additionally, the governor mechanism helps regulate engine speed by adjusting the throttle position based on load and speed, ensuring the engine maintains a stable idle when not under load.
Throttle sticking on weed eater trimmers?
Throttle cable is probably pinched somewhere, or check the butterfly on carburetor, might have a broken return spring, or debris binding the shaft.
How do you install a gas pedal spring?
Usually the throttle return spring is built into the carburetor or throttle body, depending which your vehicle has. I'm going to suggest that this is not likely your problem. Double check that there is nothing underneath the dash holding the pedal (it's common for the under dash trim to fall against the arm attached to the pedal.) There could also be something jammed in the throttle body. If after inspecting for foreign objects you still think you need a throttle return spring, it's a tricky job and it really depends on what vehicle you are working on. If you simply have a spring, then have someone move the throttle with the pedal and watch how it moves. Attach your spring so it holds it closed. Carburetors will likely have a good place to attach the spring. Throttle bodies (fuel injected cars) are meant to be replaced.
Toyota Camry throttle does not return after depressing was told the throttle body needs replaced Could it be gummed up or a bad return spring Garage wants 1000 to fix?
I believe Toyota went to a an electronic/electric throttle design in 2002. There is no mechanical connection. A spring on the accelerator pedal returns it to the start position. There are products available at the parts stores for freeing up the throttle body. If you have a car with a mechanical hook up to the throttle body you can free the cable up with products available.
If you recently changed the spark plugs on your 2000 Ford Focus and now the throttle is sticking is there any relationship between the two?
I can tell you with relative certainty that the condition and/or operation of the spark plugs should have nothing to do with a sticking throttle. Your best bet would be to check your throttle body for buildup or debris. Also you might check the throttle return spring on the side of the throttle body.
Will a Dana 35 from a 2005 wrangler bolt into a 1990 wrangler?
No. 2005 is link and coil. 1990 is leaf spring.
How many springs are in the ak-47?
Three.. bolt carrier return spring, trigger return spring, magazine release return spring.
What is the length of coil spring on 2002 wrangler?
I may be wrong but, the Wrangler has leaf springs on all 4 corners, no coils.
How do you fix a stuck throttle on 97 cavalier?
To fix a stuck throttle on a 1997 Chevrolet Cavalier, first, ensure the vehicle is off and inspect the throttle cable for any signs of damage or binding. Clean the throttle body and check for carbon buildup that might be preventing it from closing properly. If the cable is frayed or damaged, it should be replaced. Lastly, ensure that the throttle plate moves freely and that the return spring is functioning correctly.
