answersLogoWhite

0

The short answer is that it is in the same place it would be if you do have an owner's manual! The longer answer is that it is under the hood on the firewall, almost directly in front of the steering wheel. To check the brake fluid level, view the marks on the side of the reservoir, which is clear. If needed, brake fluid can be added through the lid on top. Be sure to wipe off the lid and the area surrounding the lid with a clean cloth before removing the lid. This keeps dirt out of the brake fluid.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What is the correct tire pressure for a 1998 Chevy Prizm?

Written in the owners manual and on the drivers door post.


Where is the fuse box located in a 1998 Chevy Prizm?

There are several. Refer to owners manual to find which one you need. They are under hood, under dash (driver side) and kick panels.


What is the tire size for a 1997 geo prizm?

Look in the owners' manual or on the driver's door post.


What type of Auto Trans Fluid for 2002 Chevy Prizm?

Is it manual or automatic ???? Dextron III Mercon = automatic Dextron III Mercon = Manual


Does 1999 Chevy Prizm have keyless entry?

Yes, I have a 1999 Prism with keyless entry.new answerno, not if they have manual locks.


Should you change the timing belt on a 1993 GEO Prizm with 72000 miles?

Yes, It should be changed every 70,000 miles. A owners manual or a repair manual will have the exact figures for you.


Does a 2001 Chevy Prizm have ABS?

Yes, the 2001 Chevy Prizm can come equipped with Anti-lock Braking System (ABS), but it depends on the specific trim and options chosen. Not all models had ABS as standard, so it's important to check the vehicle's specifications or consult the owner's manual to confirm whether a particular Prizm has this feature.


Is Chevy Prizm also a Nissan?

no, prizm is a re bage of Toyota collora


What could be problem if the check engine light is on in a 1998 Chevy Prizm?

There is a problem with the emissions system. You will need to have the computer scanned with a OBD2 scanner to determine where to start looking. Start by making sure all the required maintenance items have been performed, per the owners manual.


How can you put a v8 into your Chevy prizm?

Drop it in


Who is the maker for the motor of a Chevy prizm?

Toyota


Diagram of serpentine belt 2000 Chevy Prizm?

replacing serpentine belt on 2000 chevy prizm need help

Trending Questions
Install computer on dodge stratus? How many gallons does the gas tank in the 2012 Ford E-Series-VAN hold? Where is the thermostat located on 2008 dodge caliber sxt? How to reset computer on a 1998 corvette after wheel replacement now reads serv tire mon sys? Do you have old Wesco thermostats? Set timing 94 astro van? Replaced the speed sensor but speedometer still doesn't work What else can it be On a 1992 S10 Blazer Automatic 4 wheel drive. Also the check gages light stays on. HELP? When should you change the timing belt on ford focus 2001 zx3? How fast does a 2006 Dodge Charger go? Where is the fuel pressure relief valve for a 4.6L 2003 Ford Expedition? If your '92 Toyota Camry was running fine yesterday then when you tried to start it today all it would do is turn over what you should do? Where is the blower resistor located on a 1992 BMW 525i? On cold start the engine idles real high then low then high then low it does this until the car gets warm ive replaced the tps and the pcv vaulve 1995 Monte Carlo v6 3.4? Where is the stoplight switch located on a 1995 Plymouth Grand Voyager? Where can you get the pinouts for a 2001 Alero radio and you don't have the plug? How do you replace the water pump on 2000 Chevrolet S10 with 2.2 liter motor? How do you replace the GEM module on a 1996 Ford Windstar? If coolant is leaking out the weep hole of your 1982 RM125 does that mean you have a bad water pump If so can you replace that where could you purchase this or is it possible to rebuild it? What is the wheel bolt pattern for a Ford Elite 1975? You have a 1988 ford turbo coupe you tried to put new brake pads in and found that you can't push the caliper piston in so that the pads will fit the around the rotor?